SEVILLA ME
About the SEVILLA ME PCB
SEVILLA ME is an open source ESP8266 PCB design by Noxctis, published on GitHub. It is a 2-layer board measuring 120 × 100 mm, with 24 components from 18 distinct parts.
Its main chip is the ESP-01v090, from the ESP8266 family. Other key parts include the LM7805_TO220, LM1117DT-3.3, LM35-NEB, PIC16F887-IP and RC1602A-GHW-ESX. By type, the board carries 7 ICs, 6 capacitors, 5 resistors, 2 switches, 2 diodes and 1 connector.
It belongs with the sensors designs in this gallery.
Main components on the SEVILLA ME
SEVILLA ME bill of materials (BOM)
24 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM7805_TO220 | TO-220-3_Vertical | U1 |
| 1 | LM1117DT-3.3 | TO-252-3_TabPin2 | U2 |
| 1 | LM35-NEB | TO-220-3_Vertical | U3 |
| 1 | PIC16F887-IP | DIP-40_W15.24mm | U4 |
| 1 | RC1602A-GHW-ESX | RC1602A | U5 |
| 1 | TCA9517D | SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | ESP-01v090 | ESP-01 | U7 |
| 1 | Barrel_Jack_Switch | BarrelJack_Horizontal | J2 |
| 1 | R_Potentiometer | Potentiometer_ACP_CA6-H2,5_Horizontal | RV1 |
| 2 | SW_Push | SW_PUSH_6mm_H4.3mm | SW1, SW2 |
| 2 | LED | LED_2010_5025Metric_Pad1.52x2.65mm_HandSolder | D1, D2 |
| 1 | 1000uF | CP_Axial_L10.0mm_D6.0mm_P15.00mm_Horizontal | C1 |
| 2 | 0.1uF | C_Disc_D3.0mm_W2.0mm_P2.50mm | C2, C3 |
| 2 | 100uF | CP_Axial_L10.0mm_D4.5mm_P15.00mm_Horizontal | C4, C5 |
| 1 | 10uF | CP_Axial_L10.0mm_D6.0mm_P15.00mm_Horizontal | C6 |
| 1 | 1k | R_4020_10251Metric_Pad1.65x5.30mm_HandSolder | R1 |
| 3 | 10k | R_4020_10251Metric_Pad1.65x5.30mm_HandSolder | R2, R4, R5 |
| 1 | 470 | R_4020_10251Metric_Pad1.65x5.30mm_HandSolder | R3 |
SEVILLA ME design files
The KiCad project lives in the Noxctis/CpE2303L repository on GitHub; these links point at the commit this page was built from.
SEVILLA ME: common questions
What microcontroller does the SEVILLA ME use?
The SEVILLA ME is built around the ESP-01v090, from the ESP8266 family.
How big is the SEVILLA ME PCB?
The SEVILLA ME measures 120 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SEVILLA ME?
24 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the SEVILLA ME design files?
From the Noxctis/CpE2303L repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the SEVILLA ME design in my own project?
The repository has no license, so all rights stay with Noxctis. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the SEVILLA ME without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
More boards in CpE2303L
ESP8266SEVILLA Summative
120 × 100 mm24 parts2LNo license0
SEVILLA PA5-1
64.5 × 49.5 mm20 parts2LNo license0
SEVILLA PA4-1
66.8 × 60 mm19 parts2LNo license0
SEVILLA PA3-1
66.8 × 60 mm19 parts2LNo license0
Assignment: Logic Probe
77 × 36 mm18 parts2LNo license0
PICSEVILLA PA4-2
100 × 50 mm11 parts2LNo license0
PICSEVILLA PA1-3
100 × 50 mm11 parts2LNo license0
SEVILLA PA5-2
81.8 × 77.5 mm11 parts2LNo license0
Logic Circuit Example #1
36.5 × 45.5 mm11 parts2LNo license0
Logic Circuit Example #2
70 × 40 mm8 parts2LNo license0
Cpe 2303l
27.5 × 26.5 mm3 parts2LNo license0
Similar boards
ESP8266ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1k
ESP8266HASwitchPlate
aderusha
60 × 40 mm8 parts2LMIT738
ESP8266RatGDO-OpenSource-D1Mini-ESP8266
Kaldek
47.8 × 63.3 mm12 parts2LMIT506
ESP8266Goatgdo
32.9 × 53.3 mm23 parts2LMIT506
ESP8266RatGDO-OpenSource-Bare-ESP8266
55 × 82.7 mm20 parts2LMIT506
ESP8266Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398