32 open source boards using the ESP-01v090

Real designs built with the ESP-01v090, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

32 boardsClear filters|Most starred

How designs wire the ESP-01v090

Read from the KiCad layouts of 21 open source designs, one per repository: what each pin of the ESP-01v090 connects to, and the resistors, capacitors and other passives placed on it.

  • The CH_PD pin has a pull-up to 3.3V on 9 of 21 designs, most often 10 kΩ (then 2.2 kΩ).
  • The GPIO0 pin has a pull-up to 3.3V on 9 of 21 designs, most often 4.7 kΩ (then 10 kΩ).
GNDpin 2Connected to: GND 95%
CH_PDpin 3Connected to: Signal 62% · 3.3V 24%
  • Pull-up to 3.3V on 43% · 10 kΩ (5), 2.2 kΩ (1), 100 kΩ (1)
GPIO2pin 4Connected to: A connector 24% · not connected 38%
  • Pull-up to 3.3V on 33% · 4.7 kΩ (3), 10 kΩ (2), 2 kΩ (1)
GPIO0pin 6Connected to: Signal 71% · not connected 29%
  • Pull-up to 3.3V on 43% · 4.7 kΩ (4), 10 kΩ (2), 100 kΩ (1)
VCCpin 7Connected to: 3.3V 86%
  • Decoupling capacitor on 38% · 100 µF (2), 2.2 µF (1), 100 nF (1)

3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Frank by rh1tech, Teensy wifi weather logger by pdp7, Shield by xtarke and PCB Challenge - Master by D1360-64RC14.

The ESP-01v090 in open source designs

The gallery holds 32 open source boards using the ESP-01v090 from 21 GitHub repositories; a typical one measures about 74.3 × 53.2 mm and carries around 25 components.

94% are two-layer designs, the rest use four layers or more, and 59% carry an open source license.

The most starred is Megafrank by rh1tech.

Microcontrollers on boards using the ESP-01v090

ESP-01v090: common questions

Where can I find a ESP-01v090 reference design?

Each of the 32 boards on this page is a real design using the ESP-01v090. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ESP-01v090 CH_PD pin?

The CH_PD pin has a pull-up to 3.3V on 9 of 21 designs, most often 10 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 21 open source designs using the ESP-01v090.

What pull-up resistor is used on the ESP-01v090 GPIO0 pin?

The GPIO0 pin has a pull-up to 3.3V on 9 of 21 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 21 open source designs using the ESP-01v090.

What parts are used alongside the ESP-01v090?

The AMS1117-3.3, DS3231MZ, LM358, 74HC4052D,653 and 74HC595 appear in the most repositories here.

Which microcontrollers do boards using the ESP-01v090 use?

Most are built on ESP8266 (23), RP2040/RP2350 (3) and ESP32 (2).

How big is a typical board using the ESP-01v090?

The median is 74.3 × 53.2 mm, and 94% are two-layer designs.

What is the most popular open source board using the ESP-01v090?

By GitHub stars, Megafrank by rh1tech, with 65 stars.

Can I simulate one of these boards using the ESP-01v090 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part