LC DAQ
npgo22·ALI2Proposal·ground-station-loadcells-1A/load-cell.kicad_pcb
About the LC DAQ PCB
LC DAQ is an open source STM32 PCB design by npgo22, published on GitHub. It is a 4-layer board measuring 71.6 × 60 mm, with 112 components from 36 distinct parts.
Its main chip is the STM32H563RIVx, from the STM32 family. Other key parts include the USBLC6-2SC6, AP2112K-3.3, TCAN1462V, LAN8742A and ADS124S08. By type, the board carries 46 capacitors, 29 resistors, 13 diodes, 12 connectors, 6 ICs and 3 fuses.
From the project
4-layer PCB. Reads bridge-type load cells (thrust, weight).
4-layer PCB. Reads bridge-type load cells (thrust, weight).
STM32H563RIV6 - Cortex-M33, 250 MHz, 2 MB flash, 640 KB SRAM, VFQFPN68 package.
The ADS124S08 supports up to 12 single-ended or 6 differential channels, PGA gain 1–128, and built-in excitation current sources (IDAC1/IDAC2) for bridge sensor excitation. SPI Mode 1. Data rate 2.5 SPS – 4 kSPS.
crates/load-cell - Embassy async firmware, uses ads124s08 driver crate.
Main components on the LC DAQ
LC DAQ bill of materials (BOM)
112 components, 36 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USBLC6-2SC6 | SOT-23-6 | U1 |
| 1 | STM32H563RIVx | QFN-68-1EP_8x8mm_P0.4mm_EP6.4x6.4mm | U2 |
| 1 | AP2112K-3.3 | SOT-23-5 | U3 |
| 1 | TCAN1462V | SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | LAN8742A | VQFN-24-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalVias | U5 |
| 1 | ADS124S08 | VQFN-32-1EP_5x5mm_P0.5mm_EP3.15x3.15mm_ThermalVias | U6 |
| 2 | 25 MHz | 3225-4P-L | Y1, Y2 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 1 | Conn_02x06_Top_Bottom | IDC-Header_2x06_P2.54mm_Vertical | J3 |
| 1 | Screw_Terminal_01x02 | TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J4 |
| 2 | Conn_02x01 | PinHeader_2x01_P2.54mm_Vertical | J5, J6 |
| 1 | Screw_Terminal_01x05 | TerminalBlock_Phoenix_MPT-0,5-5-2.54_1x05_P2.54mm_Horizontal | J7 |
| 1 | RJ45_Hanrun_HR911105A_Horizontal | RJ45_Hanrun_HR911105A_Horizontal | J8 |
| 4 | Screw_Terminal_01x04 | TerminalBlock_Phoenix_MPT-0,5-4-2.54_1x04_P2.54mm_Horizontal | J9, J10, J11, J12 |
| 1 | Conn_02x03_Counter_Clockwise | IDC-Header_2x03_P2.54mm_Vertical | J13 |
| 3 | 500mA | Fuse_0805_2012Metric | F1, F2, F3 |
| 1 | SKRPANE010 | SKRPANE010 | SW1 |
| 5 | LED | LED_0603 | D1, D2, D3, D4, D5 |
| 8 | SMF5V0A | D_SMF | D6, D7, D8, D9, D10, D11, D12, D13 |
| 19 | 100nF | C_0603 | C1, C2, C3, C4, C5, C6, C7, C19 +11 |
Show 16 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 10pF | C_0603 | C8, C9, C27, C28 |
| 2 | 2.2uF | C_0603 | C10, C11 |
| 6 | 22uF | C_0805 | C12, C13, C14, C15, C16, C17 |
| 5 | 1uF | C_0603 | C18, C23, C32, C36, C41 |
| 1 | 470pF | C_0603 | C24 |
| 1 | 220nF | C_0603 | C26 |
| 8 | 1nF | C_0603 | C29, C31, C37, C39, C40, C44, C45, C47 |
| 2 | 4.7k | R_0603 | R1, R2 |
| 9 | 10k | R_0603 | R3, R4, R5, R6, R7, R8, R9, R16 +1 |
| 1 | 120R | R_0603 | R10 |
| 1 | 1.5k | R_0603 | R11 |
| 4 | 47R | R_0603 | R12, R13, R14, R15 |
| 1 | 12.1k | R_0603 | R17 |
| 2 | 330R | R_0603 | R19, R20 |
| 8 | 1k | R_0603 | R21, R22, R24, R25, R26, R27, R28, R29 |
| 1 | 100k | R_0603 | R23 |
LC DAQ design files
The KiCad project lives in the npgo22/ALI2Proposal repository on GitHub; these links point at the commit this page was built from.
LC DAQ: common questions
What microcontroller does the LC DAQ use?
The LC DAQ is built around the STM32H563RIVx, from the STM32 family.
How big is the LC DAQ PCB?
The LC DAQ measures 71.6 × 60 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the LC DAQ?
112 components, from 36 distinct parts. The full bill of materials is listed on this page.
Where can I download the LC DAQ design files?
From the npgo22/ALI2Proposal repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the LC DAQ design in my own project?
The repository has no license, so all rights stay with npgo22. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the LC DAQ without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in ALI2Proposal
STM32
Valve driver
npgo22
95 × 60 mm142 parts4LNo license0STM32
Pressure
npgo22
75 × 60 mm139 parts4LNo license0STM32
Thermocouple Board
npgo22
97 × 97 mm117 parts4LNo license0STM32
PT
npgo22
67 × 68 mm105 parts4LNo license0STM32
TC DAQ
npgo22
86 × 60 mm99 parts4LNo license0STM32
Chickenstick
npgo22
42 × 100 mm96 parts4LNo license0GPS Module
npgo22
43 × 34 mm24 parts4LNo license0
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k