PT

npgo22·ALI2Proposal·ground-station-pressure-transducers-1A/PT.kicad_pcb

PT PCB layout, top view — open source STM32 board by npgo22

About the PT PCB

PT is an open source STM32 PCB design by npgo22, published on GitHub. It is a 4-layer board measuring 67 × 68 mm, with 105 components from 38 distinct parts.

Its main chip is the STM32H563RITx, from the STM32 family. Other key parts include the INA241A1xD, ADS131A04, AP2112K-3.3, USBLC6-2SC6 and TJA1042T-3. By type, the board carries 46 capacitors, 26 resistors, 11 connectors, 10 ICs, 6 diodes and 3 crystals.

It belongs with the rf & radio and test & measurement designs in this gallery.

From the project

APRL ALI-2 instrumentation and control monorepo

APRL ALI-2 instrumentation and control monorepo

The ALI itself can continue to be used for years to come and this reworking of the electronics will not impact it at all. In fact, while some of the electronics designs on the ALI are used for this one, this is going to be its own separate electrical box altogether. The ALI has the following additional limitations, too: 1. Limited I/O 2. Bonded grounds between +24/12/5V power supplies 3. Unknown board-level design decisions/trade-offs made in off-the-shelf components leading to strange artifacts in various measurements 4. Is generally really…

Main components on the PT

PT bill of materials (BOM)

105 components, 38 distinct parts.

QtyPartRefs
1
STM32H563RITx
U1
4
INA241A1xD
U2, U3, U4, U5
1
ADS131A04
U6
1
AP2112K-3.3
U7
1
USBLC6-2SC6
U8
1
TJA1042T-3
U9
1
LAN8742A
U10
2
25 MHz
Y1, Y3
1
16.384 MHz
Y2
1
Conn_02x05_Odd_Even
J1
4
Conn_02x01
J2, J3, J4, J5
1
Screw_Terminal_01x02
J6
1
USB_C_Receptacle_USB2.0_16P
J7
2
Conn_02x01
J8, J9
1
Screw_Terminal_01x05
J10
1
RJ45_Hanrun_HR911105A_Horizontal
J11
1
100mA Hold
F1
1
500mA
F2
1
SW_MEC_5E
SW1
3
LED
D1, D2, D3
Show 18 more
QtyPartRefs
3
LED_Small
D4, D5, D6
6
10pF
C1, C3, C25, C27, C39, C41
7
1uF
C2, C20, C21, C22, C28, C38, C44
19
100nF
C4, C5, C6, C8, C10, C11, C12, C13 +11
2
2.2uF
C7, C9
4
6.8nF
C16, C17, C18, C19
6
22uF
C29, C30, C31, C32, C33, C34
1
470pF
C45
1
220nF
C46
6
10k
R1, R2, R3, R13, R14, R19
4
13R
R4, R5, R6, R7
6
330R
R8, R9, R10, R11, R25, R26
1
150k
R12
2
4.7k
R15, R16
1
120R
R17
1
1.5k
R18
4
47R
R20, R21, R23, R24
1
12.1k
R22

PT design files

The KiCad project lives in the npgo22/ALI2Proposal repository on GitHub; these links point at the commit this page was built from.

PT: common questions

What microcontroller does the PT use?

The PT is built around the STM32H563RITx, from the STM32 family.

How big is the PT PCB?

The PT measures 67 × 68 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the PT?

105 components, from 38 distinct parts. The full bill of materials is listed on this page.

Where can I download the PT design files?

From the npgo22/ALI2Proposal repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the PT design in my own project?

The repository has no license, so all rights stay with npgo22. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the PT without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in ALI2Proposal

Similar boards