Pressure
npgo22·ALI2Proposal·ground-station-pressure-transducers-1B/pressure.kicad_pcb
About the Pressure PCB
Pressure is an open source STM32 PCB design by npgo22, published on GitHub. It is a 4-layer board measuring 75 × 60 mm, with 139 components from 38 distinct parts.
Its main chip is the STM32H563RIVx, from the STM32 family. Other key parts include the USBLC6-2SC6, AP2112K-3.3, TCAN1462V, LAN8742A and ADS131A04. By type, the board carries 56 capacitors, 45 resistors, 16 connectors, 7 ICs, 6 diodes and 4 crystals.
From the project
4-layer PCB. Reads pressure transducers across the propellant and pressurant system.
4-layer PCB. Reads pressure transducers across the propellant and pressurant system.
STM32H563RIV6 - Cortex-M33, 250 MHz, 2 MB flash, 640 KB SRAM, VFQFPN68 package.
The ADS131A04 samples all 4 channels simultaneously, which eliminates phase error between channels. PGA gain 1–128 per channel. Data rate up to 32 kSPS. SPI Mode 1.
crates/pressure - Embassy async firmware, uses ads131a04 driver crate.
Main components on the Pressure
Pressure bill of materials (BOM)
139 components, 38 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USBLC6-2SC6 | SOT-23-6 | U1 |
| 1 | STM32H563RIVx | QFN-68-1EP_8x8mm_P0.4mm_EP6.4x6.4mm | U2 |
| 1 | AP2112K-3.3 | SOT-23-5 | U3 |
| 1 | TCAN1462V | SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | LAN8742A | VQFN-24-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalVias | U5 |
| 2 | ADS131A04 | QFP-32_5x5_Pitch0.5mm | U6, U7 |
| 2 | 25 MHz | 3225-4P-L | Y1, Y2 |
| 2 | 16.384 MHz | 3225-4P-L | Y3, Y4 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 2 | Screw_Terminal_01x02 | TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J3, J5 |
| 1 | Conn_02x06_Top_Bottom | IDC-Header_2x06_P2.54mm_Vertical | J4 |
| 2 | Conn_02x01 | PinHeader_2x01_P2.54mm_Vertical | J6, J7 |
| 1 | Screw_Terminal_01x05 | TerminalBlock_Phoenix_MPT-0,5-5-2.54_1x05_P2.54mm_Horizontal | J8 |
| 1 | RJ45_Hanrun_HR911105A_Horizontal | RJ45_Hanrun_HR911105A_Horizontal | J9 |
| 8 | Conn_02x01 | TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J10, J11, J12, J13, J14, J15, J16, J17 |
| 3 | 500mA | Fuse_0805_2012Metric | F1, F3, F4 |
| 1 | 100mA Hold | Fuse_0805_2012Metric | F2 |
| 1 | SKRPANE010 | SKRPANE010 | SW1 |
| 6 | LED | LED_0603 | D1, D2, D3, D4, D5, D6 |
| 20 | 100nF | C_0603 | C1, C2, C3, C4, C5, C6, C7, C19 +12 |
Show 18 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 10pF | C_0603 | C8, C9, C27, C28 |
| 2 | 2.2uF | C_0603 | C10, C11 |
| 6 | 22uF | C_0805 | C12, C13, C14, C15, C16, C17 |
| 10 | 1uF | C_0603 | C18, C23, C34, C35, C37, C38, C48, C49 +2 |
| 1 | 470pF | C_0603 | C24 |
| 1 | 220nF | C_0603 | C26 |
| 8 | 10nF | C_0603 | C29, C36, C39, C42, C43, C50, C53, C56 |
| 4 | 30pF | C_0603 | C40, C41, C54, C55 |
| 2 | 4.7k | R_0603 | R1, R2 |
| 1 | 150k | R_0603 | R3 |
| 9 | 10k | R_0603 | R4, R5, R6, R7, R8, R9, R10, R17 +1 |
| 1 | 120R | R_0603 | R11 |
| 1 | 1.5k | R_0603 | R12 |
| 4 | 47R | R_0603 | R13, R14, R15, R16 |
| 1 | 12.1k | R_0603 | R18 |
| 2 | 330R | R_0603 | R20, R21 |
| 16 | 100R | R_0603 | R22, R24, R25, R27, R28, R30, R31, R33 +8 |
| 8 | 100R | R_0805 | R23, R26, R29, R32, R35, R38, R41, R44 |
Pressure design files
The KiCad project lives in the npgo22/ALI2Proposal repository on GitHub; these links point at the commit this page was built from.
Pressure: common questions
What microcontroller does the Pressure use?
The Pressure is built around the STM32H563RIVx, from the STM32 family.
How big is the Pressure PCB?
The Pressure measures 75 × 60 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Pressure?
139 components, from 38 distinct parts. The full bill of materials is listed on this page.
Where can I download the Pressure design files?
From the npgo22/ALI2Proposal repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Pressure design in my own project?
The repository has no license, so all rights stay with npgo22. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Pressure without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in ALI2Proposal
STM32
Valve driver
npgo22
95 × 60 mm142 parts4LNo license0STM32
Thermocouple Board
npgo22
97 × 97 mm117 parts4LNo license0STM32
LC DAQ
npgo22
71.6 × 60 mm112 parts4LNo license0STM32
PT
npgo22
67 × 68 mm105 parts4LNo license0STM32
TC DAQ
npgo22
86 × 60 mm99 parts4LNo license0STM32
Chickenstick
npgo22
42 × 100 mm96 parts4LNo license0GPS Module
npgo22
43 × 34 mm24 parts4LNo license0
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k