Jantteri hit detector
About the Jantteri hit detector PCB
Jantteri hit detector is an open source STM32 PCB design by OJ2016, published on GitHub. It is a 2-layer board measuring 80 × 15.1 mm, with 30 components from 15 distinct parts.
Its main chip is the STM32G030C8T6, from the STM32 family. Other key parts include the LIS2DW12TR and AMS1117-3.3. By type, the board carries 17 capacitors, 5 ICs, 2 connectors, 2 resistors, 1 transistor and 1 crystal.
Main components on the Jantteri hit detector
Jantteri hit detector bill of materials (BOM)
30 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32G030C8T6 | LQFP-48_7x7mm_P0.5mm | U1 |
| 3 | LIS2DW12TR | LGA-12_2x2mm_P0.5mm | U3, U4, U5 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U6 |
| 1 | IRLML6402TRPBF | SOT-23 | Q1 |
| 1 | 16MHZ 16MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | Conn_01x04_Male | JST_ZH_B4B-ZR_1x04_P1.50mm_Vertical | J1 |
| 1 | Conn_02x03_Odd_Even | Tag-Connect_TC2030-IDC-FP_2x03_P1.27mm_Vertical | J2 |
| 1 | LED | LED_0603_1608Metric | D1 |
| 1 | GZ2012D101TF | L_0805_2012Metric | FB1 |
| 1 | 4U7 4u7 | C_1206_3216Metric | C1 |
| 12 | 100N 100n | C_0603_1608Metric | C2, C3, C4, C5, C6, C7, C12, C13 +4 |
| 2 | 12P 12p | C_0402_1005Metric | C8, C9 |
| 2 | 10U 10u | C_0805_2012Metric | C18, C19 |
| 1 | 47 | R_0402_1005Metric | R1 |
| 1 | 1K5 1k5 | R_0402_1005Metric | R2 |
Jantteri hit detector design files
The KiCad project lives in the OJ2016/pcb-common repository on GitHub; these links point at the commit this page was built from.
Jantteri hit detector: common questions
What microcontroller does the Jantteri hit detector use?
The Jantteri hit detector is built around the STM32G030C8T6, from the STM32 family.
How big is the Jantteri hit detector PCB?
The Jantteri hit detector measures 80 × 15.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Jantteri hit detector?
30 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Jantteri hit detector design files?
From the OJ2016/pcb-common repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Jantteri hit detector design in my own project?
The repository has no license, so all rights stay with OJ2016. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Jantteri hit detector without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in pcb-common
Jantteri right
63.8 × 63.8 mm89 parts2LNo license1
STM32Jantteri motor pwr
137.7 × 45 mm72 parts2LNo license1
Jantteri secondary
90.6 × 20.3 mm58 parts2LNo license1
STM32Jantteri left
63.8 × 63.8 mm55 parts2LNo license1
Jantteri testrack interface
130.2 × 51.8 mm53 parts2LNo license1
STM32Jantteri motor pwr old
40 × 80.7 mm52 parts2LNo license1
ESP32Jantteri main
78.5 × 34.3 mm44 parts2LNo license1
STM32Jantteri lora
40.2 × 17.5 mm24 parts2LNo license1
Eth uart breakout
60 × 39.3 mm14 parts2LNo license1
Similar boards
STM32AxxSolder
AxxAxx
39 × 82.5 mm122 parts2LGPL-3.01.7k
STM32AIOC
skuep
21 × 31.5 mm47 parts2LMIT1.4k
STM32Ferris
pierrechevalier83
208.8 × 86.8 mm102 parts2LSHL-2.11.3k
STM32Module 16S
stuartpittaway
71.1 × 89.6 mm113 parts4LCC-BY-NC-4.01.1k
STM32Djinn
tzarc
192.3 × 150.5 mm216 parts2LCERN-OHL-S-2.0988
STM32Ghoul
228.6 × 79.4 mm163 parts2LCERN-OHL-S-2.0988