ESP32 Falcon
Patkra77111·ESP32_Falcon
About the ESP32 Falcon PCB
ESP32 Falcon is an open source ESP32 PCB design by Patkra77111, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 50 × 61 mm, with 28 components from 17 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the USBLC6-2SC6, AMS1117-3.3 and BMI270. By type, the board carries 9 resistors, 5 capacitors, 4 ICs, 3 connectors, 2 diodes and 1 fuse.
It belongs with the sensors designs in this gallery.
From the project
This is custom ESP32 board with the IMU BMI270.
Main components on the ESP32 Falcon
ESP32 Falcon bill of materials (BOM)
28 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U2 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U3 |
| 1 | BMI270 | BMI270_BOS | U4 |
| 1 | USB_C_RECEPTACLE_USB2.0_16P USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_XKB_U262-16XN-4BVC11 | J1 |
| 2 | CONN_01X15_PIN Conn_01x15_Pin | PinHeader_1x15_P2.54mm_Vertical | J2, J3 |
| 3 | SW_Push | SW_Push_1TS009xxxx-xxxx-xxxx_6x6x5mm | BOOT1, EN1, USER_BUTTON1 |
| 1 | 1A | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F2 |
| 2 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 1 | BLM21PG221 | L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | FB2 |
| 2 | 0.1U 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3 |
| 2 | 22u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2_tantalum, C3_tantalum |
| 1 | 1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4 |
| 2 | 5K1 5k1 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 3 | 10K 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R6, R9 |
| 2 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R5 |
| 2 | 4.7K 4.7k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7, R8 |
ESP32 Falcon design files
The KiCad project lives in the Patkra77111/ESP32_Falcon repository on GitHub; these links point at the commit this page was built from.
- LayoutESP32_Falcon.kicad_pcb
- SchematicESP32_Falcon.kicad_sch
- BOMESP32_Falcon_BOM.csv
ESP32 Falcon: common questions
What microcontroller does the ESP32 Falcon use?
The ESP32 Falcon is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the ESP32 Falcon PCB?
The ESP32 Falcon measures 50 × 61 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32 Falcon?
28 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ESP32 Falcon design files?
From the Patkra77111/ESP32_Falcon repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ESP32 Falcon design in my own project?
Yes, under the terms of its Apache-2.0 license, which Patkra77111 chose for the repository.
Can I test firmware for the ESP32 Falcon without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k