Esp32-devboard
pazambranosauc·esp32-devboard·hardware/Customized ESP-32.kicad_pcb
About the Esp32-devboard PCB
Esp32-devboard is an open source ESP32 PCB design by pazambranosauc, published on GitHub. It is a 2-layer board measuring 30 × 64 mm, with 26 components from 14 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the AMS1117-3.3 and CP2102N-Axx-xQFN24. By type, the board carries 9 resistors, 7 capacitors, 3 ICs, 3 connectors, 2 transistors and 2 switches.
It belongs with the dev boards & breakouts and usb & debug tools designs in this gallery.
From the project
Two-layer ESP32-WROOM-32 dev board in KiCad: USB-C, CP2102N with auto-reset, AMS1117, breadboard headers. Rev B after a design review of rev A.
A two-layer ESP32-WROOM-32 development board designed from a blank schematic: USB-C, an AMS1117-3.3 regulator, a CP2102N USB-UART bridge with two-transistor auto-reset, and two breadboard-spaced 20-pin headers. It's sized for hand assembly: 0603 passives, 1206 tantalums, 2.54 mm headers.
Status: Rev B layout complete, not yet fabricated. Rev A was cancelled before production after a design review found three faults (below). Bring-up results will be added here once the boards arrive.

Main components on the Esp32-devboard
Esp32-devboard bill of materials (BOM)
26 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U2 |
| 1 | CP2102N-Axx-xQFN24 | QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U3 |
| 2 | MMBT3904 | SOT-23 | Q1, Q2 |
| 2 | Conn_01x20_Pin | PinHeader_1x20_P2.54mm_Vertical | J1, J2 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | P1 |
| 2 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 2 | 10μF | CP_EIA-3216-18_Kemet-A_HandSolder | C1, C9 |
| 3 | 100nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C4, C8 |
| 1 | 10µF | CP_EIA-3216-18_Kemet-A_HandSolder | C3 |
| 1 | 1µF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C5 |
| 6 | 10kΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R5, R7, R8, R10, R11 |
| 2 | 5.1kΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3 |
| 1 | 1MΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
Esp32-devboard design files
The KiCad project lives in the pazambranosauc/esp32-devboard repository on GitHub; these links point at the commit this page was built from.
Esp32-devboard: common questions
What microcontroller does the Esp32-devboard use?
The Esp32-devboard is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the Esp32-devboard PCB?
The Esp32-devboard measures 30 × 64 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-devboard?
26 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32-devboard design files?
From the pazambranosauc/esp32-devboard repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp32-devboard design in my own project?
The repository has no license, so all rights stay with pazambranosauc. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32-devboard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k