Esp32-s2 corebase
pedrominatel·esp32-s2_corebase·esp32-s2_corebase/esp32-s2_corebase.kicad_pcb
About the Esp32-s2 corebase PCB
Esp32-s2 corebase is an open source ESP32 PCB design by pedrominatel, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 22.9 × 41.3 mm, with 45 components from 21 distinct parts.
Its main chip is the ESP32-S2, from the ESP32 family. Other key parts include the PSRAM, W25Q128JVS and TLV75733PDBV. By type, the board carries 23 capacitors, 8 resistors, 4 ICs, 4 connectors, 2 crystals and 2 inductors.
From the project
This is the base template for the ESP32-S2 SoC projects.
Main components on the Esp32-s2 corebase
Esp32-s2 corebase bill of materials (BOM)
45 components, 21 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | PSRAM | SOIC-8_5.275x5.275mm_P1.27mm | U1 |
| 1 | W25Q128JVS | SOIC-8_5.275x5.275mm_P1.27mm | U2 |
| 1 | ESP32-S2 | QFN-56-1EP_7x7mm_P0.4mm_EP5.6x5.6mm | U3 |
| 1 | TLV75733PDBV | SOT-23-5 | U4 |
| 1 | 40MHz 10ppm | CRYSTAL-SMD-3.2X2.5MM | Y1 |
| 1 | 32kHz | CRYSTAL-SMD-3.2X1.5MM | Y2 |
| 1 | Conn_01x06 | PinHeader_1x06_P1.27mm_Vertical | J1 |
| 2 | Conn_01x16 | PinHeader_1x16_P1.27mm_Vertical | J2, J4 |
| 1 | Conn_ARM_JTAG_SWD_10 | PinHeader_2x05_P1.27mm_Vertical_SMD | J3 |
| 1 | ANT3216LL00R2400A | ANTC3216X135N | ANT1 |
| 1 | LESD8D3.3CAT5G | SC70 | D1 |
| 1 | 0R | L_0402_1005Metric | L1 |
| 1 | 2nH | L_0402_1005Metric | L2 |
| 13 | 100nF | C_0402_1005Metric | C1, C8, C9, C10, C11, C12, C13, C14 +5 |
| 4 | 10pF | C_0402_1005Metric | C2, C3, C6, C7 |
| 2 | ? | C_0402_1005Metric | C4, C5 |
| 3 | 1uF | C_0603_1608Metric | C18, C19, C22 |
| 1 | 10uF | CP_EIA-3216-12_Kemet-S | C23 |
| 1 | 10kR DNP | R_0402_1005Metric | R1 |
| 5 | 10kR | R_0402_1005Metric | R2, R3, R4, R5, R8 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 499R | R_0402_1005Metric | R6, R7 |
Esp32-s2 corebase design files
The KiCad project lives in the pedrominatel/esp32-s2_corebase repository on GitHub; these links point at the commit this page was built from.
Esp32-s2 corebase: common questions
What microcontroller does the Esp32-s2 corebase use?
The Esp32-s2 corebase is built around the ESP32-S2, from the ESP32 family.
How big is the Esp32-s2 corebase PCB?
The Esp32-s2 corebase measures 22.9 × 41.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-s2 corebase?
45 components, from 21 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32-s2 corebase design files?
From the pedrominatel/esp32-s2_corebase repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Esp32-s2 corebase design in my own project?
Yes, under the terms of its GPL-3.0 license, which pedrominatel chose for the repository.
Can I test firmware for the Esp32-s2 corebase without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k