Ac vent controller
Pierowheelz·ac-vent-controller·Circuit Board V2/Circuit Board V2.kicad_pcb
About the Ac vent controller PCB
Ac vent controller is an open source ESP32 PCB design by Pierowheelz, published on GitHub. It is a 2-layer board measuring 89.5 × 49 mm, with 15 components from 6 distinct parts.
Its main chip is the TMC2209_SILENTSTEPSTICK, from the ESP32 family. Other key parts include the DEVKIT_V1_ESP32-WROOM-32 and TSR1-2433E. By type, the board carries 6 ICs, 4 modules, 4 switches and 1 connector.
It belongs with the robotics & motion, iot & wireless and power & battery designs in this gallery.
From the project
ESP32-based controller for Aircon Vents with stepper motors.
Note: There is no security or authentication in this system. Do not open up the port in your Router! For use on your internal network only.
Open vent #1 to 100%: GET http://192.168.2.110/?a=6&t=1&m=0&d=100 Here a is the operating mode, where mode 6 corresponds to: open to ratio set by &d= (eg. ?d=050:open50%, ?d=000:close, ?d=100:open100%). Also, t is the response type (1 = JSON). And, m is the motor number (0-2).

Main components on the Ac vent controller
Ac vent controller bill of materials (BOM)
15 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | TMC2209_SILENTSTEPSTICK | MODULE_TMC2209_SILENTSTEPSTICK | U1, U2, U3, U6 |
| 1 | DEVKIT_V1_ESP32-WROOM-32 | MODULE_DEVKIT_V1_ESP32-WROOM-32 | U4 |
| 1 | TSR1-2433E | Converter_DCDC_TRACO_TSR1-xxxxE_THT | U5 |
| 4 | Stepper_Motor_bipolar | PinHeader_1x04_P2.54mm_Vertical | M1, M2, M3, M4 |
| 1 | Barrel_Jack_MountingPin | BarrelJack_Horizontal | J1 |
| 4 | SW_SPDT | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW1, SW2, SW3, SW4 |
Ac vent controller design files
The KiCad project lives in the Pierowheelz/ac-vent-controller repository on GitHub; these links point at the commit this page was built from.
Ac vent controller: common questions
What microcontroller does the Ac vent controller use?
The Ac vent controller is built around the TMC2209_SILENTSTEPSTICK, from the ESP32 family.
How big is the Ac vent controller PCB?
The Ac vent controller measures 89.5 × 49 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Ac vent controller?
15 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Ac vent controller design files?
From the Pierowheelz/ac-vent-controller repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Ac vent controller design in my own project?
The repository has no license, so all rights stay with Pierowheelz. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Ac vent controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k