Batmon
pjaos·batmon·hardware/schemtic_pcb/batmon.kicad_pcb
About the Batmon PCB
Batmon is an open source ESP32 PCB design by pjaos, published on GitHub under the MIT license. It is a 2-layer board measuring 87 × 33 mm, with 57 components from 34 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the LM2576HVS-ADJ, LM1117-3.3 and ADS1115IDGS. By type, the board carries 20 resistors, 16 capacitors, 6 connectors, 5 diodes, 4 ICs and 2 transistors.
It belongs with the iot & wireless and power & battery designs in this gallery.
From the project
A device to assist in extending the life of EBike batteries.
For example if the maximum charge voltage of a Lithium ION cell is set to 4.1 volts per cell rather than the maximum of 4.2 volts per cell then the number of charge/discharge cycles that the battery is capable of could be doubled. The trade off for this is that you will loose about 10 % of the range on a single charge. If set to 4.0 volts per cell then the number of charge/discharge cycles that the battery is capable of could be increased by four times. The trade off for this is that you will loose about 25 % of the range on a single charge. The batmon device allows the user to set this trade…

Main components on the Batmon
Batmon bill of materials (BOM)
57 components, 34 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM2576HVS-ADJ | TO-220-5_Vertical | U2 |
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U3 |
| 1 | LM1117-3.3 | SOT-223-3_TabPin2 | U4 |
| 1 | ADS1115IDGS | TSSOP-10_3x3mm_P0.5mm | U5 |
| 1 | IRF520N | TO-220-3_Vertical | Q1 |
| 1 | 2N7002 | TSOT-23 | Q2 |
| 1 | XT60 Connector | AMASS_XT60-F_1x02_P7.20mm_Vertical | J1 |
| 2 | CONN_01X06 Conn_01x06 | PinHeader_1x06_P2.54mm_Vertical | J5, J6 |
| 1 | SW_&_LED | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J7 |
| 1 | Serial Console | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J8 |
| 1 | MCP9700 | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J9 |
| 1 | nn 5A | Scherter_OMT125 | F1 |
| 1 | Reset | switch_SPST_5mmx3mmx2.5mm | SW1 |
| 1 | WiFi | switch_SPST_5mmx3mmx2.5mm | SW2 |
| 1 | SS36 | D_MELF | D1 |
| 1 | 10V | D_MELF | D2 |
| 1 | LED | D_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D3 |
| 2 | 4V7 | SOT-23 | D4, D5 |
| 1 | 100UH 100uH | Sumida_CDRH74 | L1 |
| 1 | 100UF 100uf | CP_Radial_D10.0mm_P5.00mm | C1 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | DNF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C5 |
| 9 | 0.1UF 0.1uf | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C6, C8, C10, C11, C12, C13, C15 +1 |
| 1 | 1000uf 16v | CP_Radial_D10.0mm_P5.00mm | C4 |
| 1 | DNF | CP_EIA-6032-20_AVX-F_Pad2.25x2.35mm_HandSolder | C7 |
| 2 | 10UF 10uf | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C9, C14 |
| 3 | 4K7 4k7 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R9, R10 |
| 1 | 1K5 1k5 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | 5K6 5k6 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 2 | 22K 22k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R20 |
| 1 | 100K | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5 |
| 2 | 10K 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R7 |
| 1 | 470R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8 |
| 5 | 1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11, R12, R13, R18, R19 |
| 4 | 0.16R | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R14, R15, R16, R17 |
Batmon design files
The KiCad project lives in the pjaos/batmon repository on GitHub; these links point at the commit this page was built from.
Batmon: common questions
What microcontroller does the Batmon use?
The Batmon is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the Batmon PCB?
The Batmon measures 87 × 33 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Batmon?
57 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Batmon design files?
From the pjaos/batmon repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Batmon design in my own project?
Yes, under the terms of its MIT license, which pjaos chose for the repository.
Can I test firmware for the Batmon without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k