6 open source boards using the LM2576HVS-ADJ
Real designs built with the LM2576HVS-ADJ, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
VFO-ESP32-Si5351
paulh002
108.4 × 79.9 mm95 parts2LNo license29PiZero VT100
rzuehlsd
99.7 × 99.7 mm40 parts2LNo license10SMPS-Board
AlecRossCS
38.1 × 63.5 mm18 parts2LMIT2ESP32
Batmon
pjaos
87 × 33 mm57 parts2LMIT1STM32
MareapPowerBoard
RandBeyy
90 × 70 mm69 parts2LNo license0LM2576 Var Volt Reg
ReadHeadRedemption
48 × 48.2 mm14 parts2LNo license0
How designs wire the LM2576HVS-ADJ
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LM2576HVS-ADJ connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin has a inductor on 6 of 6 designs, most often 100 µH (then 47 µH).
- The FB pin has a resistor to GND on 6 of 6 designs, most often 1 kΩ (then 3.9 kΩ).
- The ON/OFF pin is tied to GND on 5 of 6 designs.
- The VIN pin has a capacitor to GND on 4 of 6 designs, most often 10 µF (then 100 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: A connector 33% · BATT 33% |
|
| OUTpin 2 | Connected to: Signal 100% |
|
| GNDpin 3 | Connected to: GND 100% | — |
| FBpin 4 | Connected to: Signal 100% |
|
| ON/OFFpin 5 | Connected to: GND 83% · a signal 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include VFO-ESP32-Si5351 by paulh002, PiZero VT100 by rzuehlsd, SMPS-Board by AlecRossCS and Batmon by pjaos.
The LM2576HVS-ADJ in open source designs
The gallery holds 6 open source boards using the LM2576HVS-ADJ from 6 GitHub repositories; a typical one measures about 88.5 × 66.8 mm and carries around 49 components.
100% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is VFO-ESP32-Si5351 by paulh002.
What boards using the LM2576HVS-ADJ are built for
LM2576HVS-ADJ: common questions
Where can I find a LM2576HVS-ADJ reference design?
Each of the 6 boards on this page is a real design using the LM2576HVS-ADJ. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM2576HVS-ADJ OUT pin connected?
The OUT pin has a inductor on 6 of 6 designs, most often 100 µH (then 47 µH). Counted from the KiCad layouts of 6 open source designs using the LM2576HVS-ADJ.
What resistor goes on the LM2576HVS-ADJ FB pin?
The FB pin has a resistor to GND on 6 of 6 designs, most often 1 kΩ (then 3.9 kΩ). Counted from the KiCad layouts of 6 open source designs using the LM2576HVS-ADJ.
How is the LM2576HVS-ADJ ON/OFF pin connected?
The ON/OFF pin is tied to GND on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the LM2576HVS-ADJ.
Which microcontrollers do boards using the LM2576HVS-ADJ use?
Most are built on ESP32 (2) and STM32 (1).
How big is a typical board using the LM2576HVS-ADJ?
The median is 88.5 × 66.8 mm, and 100% are two-layer designs.
What is the most popular open source board using the LM2576HVS-ADJ?
By GitHub stars, VFO-ESP32-Si5351 by paulh002, with 29 stars.
Can I simulate one of these boards using the LM2576HVS-ADJ before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.