Protocentral easyemg hardware
Protocentral·protocentral_easyemg_hardware·hardware/easyEMG_v2.kicad_pcb
About the Protocentral easyemg hardware PCB
Protocentral easyemg hardware is an open source PCB design by Protocentral, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 40 × 28.8 mm, with 46 components from 25 distinct parts.
Other key parts include the AP2112K-3.3, BSS138DW-7-F, USBLC6-4SC6, TLA2024IRUGR and INA333xxDGK. By type, the board carries 20 resistors, 15 capacitors, 7 ICs and 2 connectors.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Protocentral easyEMG surface EMG breakout: hardware design files (CERN-OHL-P v2)
Open-source hardware design files for the Protocentral easyEMG Breakout, a single-channel surface EMG (sEMG) board on I²C / Qwiic. It's built from parts you can probe: a TI INA333 instrumentation amplifier, two TI OPA2333 op-amps and a TI TLA2024 12-bit ADC.
Unlike an analog "muscle sensor", it outputs the raw band-limited waveform over I²C; the RMS envelope is computed in the library.

Main components on the Protocentral easyemg hardware
Protocentral easyemg hardware bill of materials (BOM)
46 components, 25 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP2112K-3.3 | SOT-23-5 | U1 |
| 1 | BSS138DW-7-F | SOT-363_SC-70-6 | U2 |
| 1 | USBLC6-4SC6 | SOT-23-6 | U3 |
| 1 | TLA2024IRUGR | IC_TLA2024IRUGR | U4 |
| 1 | INA333xxDGK | VSSOP-8_3x3mm_P0.65mm | U7 |
| 2 | OPA2333xxDGK | VSSOP-8_3x3mm_P0.65mm | U8, U9 |
| 1 | AudioJack3 | Jack_3.5mm_CUI_SJ-3523-SMT_Horizontal | J3 |
| 1 | Conn_01x04 | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 2 | Qwiic_RA | JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | QW1, QW2 |
| 3 | 1u | C_0402_1005Metric | C1, C6, C13 |
| 1 | 2.2u | C_0402_1005Metric | C2 |
| 5 | 100n | C_0402_1005Metric | C4, C7, C10, C11, C17 |
| 2 | 10n | C_0402_1005Metric | C8, C9 |
| 3 | 100p | C_0402_1005Metric | C12, C15, C16 |
| 1 | 1n | C_0402_1005Metric | C14 |
| 8 | 10k | R_0402_1005Metric | R1, R2, R3, R4, R11, R12, R24, R25 |
| 1 | 10k 1% | R_0402_1005Metric | R10 |
| 1 | 9.1k 1% | R_0402_1005Metric | R13 |
| 1 | 100k 1% | R_0402_1005Metric | R14 |
| 2 | 100k | R_0402_1005Metric | R15, R16 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 33k | R_0402_1005Metric | R17, R18 |
| 1 | 27k 1% | R_0402_1005Metric | R19 |
| 2 | 1M | R_0402_1005Metric | R20, R23 |
| 1 | 10M | R_0402_1005Metric | R21 |
| 1 | 390k | R_0402_1005Metric | R22 |
Protocentral easyemg hardware design files
The KiCad project lives in the Protocentral/protocentral_easyemg_hardware repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/easyEMG_v2.kicad_pcb
- Schematichardware/easyEMG_v2.kicad_sch
Protocentral easyemg hardware: common questions
How big is the Protocentral easyemg hardware PCB?
The Protocentral easyemg hardware measures 40 × 28.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Protocentral easyemg hardware?
46 components, from 25 distinct parts. The full bill of materials is listed on this page.
Where can I download the Protocentral easyemg hardware design files?
From the Protocentral/protocentral_easyemg_hardware repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Protocentral easyemg hardware design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which Protocentral chose for the repository.
Similar boards
Breakout 112pin Connector
rusefi
174 × 58 mm39 parts2LGPL-3.01.2kEecv breakout
rusefi
140.8 × 53.7 mm9 parts4LGPL-3.01.2kBreakout 60pin EEC-IV
rusefi
139.7 × 62.2 mm15 parts2LGPL-3.01.2k134pin 7-967288-1
rusefi
139.7 × 73.7 mm38 parts2LGPL-3.01.2k88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2kRj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979