16 open source boards using the INA333xxDGK
Real designs built with the INA333xxDGK, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Milliohm meter
gabeak2
59.7 × 54.6 mm32 parts4LGPL-3.03STM32
CurrentSensingCircuit
Michalek007
100 × 50 mm77 parts4LNo license1STM32
Axon
paulodietricheng
43.9 × 55.6 mm67 parts4LNo license1Protocentral easyecg hardware
Protocentral
40 × 28.8 mm46 parts2LCERN-OHL-P-2.01Protocentral easyemg hardware
Protocentral
40 × 28.8 mm46 parts2LCERN-OHL-P-2.01ESP32
Thermocouple new
Daniele21211
99 × 67 mm215 parts4LNo license0EMG-HW-SigAcq
N-Pulse
50 × 28 mm55 parts4LCC-BY-4.00ESP32
Piezometer
Daniele21211
99.7 × 66.9 mm161 parts2LNo license0EMGSensor
SonDinh23
16 × 28 mm40 parts4LGPL-3.00EMG SENSOR
SonDinh23
16 × 28 mm43 parts4LGPL-3.0424Pin
hlord2000
34.7 × 30.6 mm14 parts4LNo license024PinINA333
hlord2000
34.7 × 30.6 mm14 parts4LNo license0TC kent
BlueJayRacing
32.5 × 17 mm9 parts2LNo license0INA333
hlord2000
34.7 × 30.6 mm7 parts2LNo license0Thermistor circuit
BlueJayRacing
31 × 16 mm9 parts2LNo license0TC shuwen
BlueJayRacing
28 × 20 mm8 parts2LNo license0
How designs wire the INA333xxDGK
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the INA333xxDGK connects to, and the resistors, capacitors and other passives placed on it.
- The RG pins have a series resistor on 10 of 11 designs, most often 100 Ω (then 10 kΩ).
- The V+ pin has a decoupling capacitor on 10 of 11 designs, most often 100 nF (then 4.7 µF).
- The V- pin is tied to GND on 8 of 11 designs (-3.3V on 3).
- Pin 6 has a series resistor on 6 of 11 designs, most often 3.6 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RGpin 1, 8 | Connected to: Signal 91% |
|
| -pin 2 | Connected to: A connector 45% |
|
| +pin 3 | Connected to: A connector 55% |
|
| V-pin 4 | Connected to: GND 73% · -3.3V 27% | — |
| REFpin 5 | Connected to: Signal 45% · GND 27% · VREF 27% |
|
| Pin 6 | Connected to: A connector 27% |
|
| V+pin 7 | Connected to: 3.3V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EMG SENSOR by SonDinh23, Milliohm meter by gabeak2, CurrentSensingCircuit by Michalek007 and Axon by paulodietricheng.
The INA333xxDGK in open source designs
The gallery holds 16 open source boards using the INA333xxDGK from 11 GitHub repositories; a typical one measures about 37.4 × 29.7 mm and carries around 42 components.
56% use four copper layers or more, and 38% carry an open source license.
The most starred is EMG SENSOR by SonDinh23.
Parts used alongside the INA333xxDGK
What boards using the INA333xxDGK are built for
INA333xxDGK: common questions
Where can I find a INA333xxDGK reference design?
Each of the 16 boards on this page is a real design using the INA333xxDGK. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the INA333xxDGK RG pin?
The RG pins have a series resistor on 10 of 11 designs, most often 100 Ω (then 10 kΩ). Counted from the KiCad layouts of 11 open source designs using the INA333xxDGK.
What decoupling capacitors do designs use on the INA333xxDGK V+ pin?
The V+ pin has a decoupling capacitor on 10 of 11 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 11 open source designs using the INA333xxDGK.
How is the INA333xxDGK V- pin connected?
The V- pin is tied to GND on 8 of 11 designs (-3.3V on 3). Counted from the KiCad layouts of 11 open source designs using the INA333xxDGK.
What parts are used alongside the INA333xxDGK?
The AP2112K-3.3, BSS138DW-7-F, OPA2333xxDGK, Pad_Battery and TLA2024IRUGR appear in the most repositories here.
Which microcontrollers do boards using the INA333xxDGK use?
Most are built on ESP32 (2) and STM32 (2).
How big is a typical board using the INA333xxDGK?
The median is 37.4 × 29.7 mm, and 44% are two-layer designs.
What is the most popular open source board using the INA333xxDGK?
By GitHub stars, EMG SENSOR by SonDinh23, with 4 stars.
Can I simulate one of these boards using the INA333xxDGK before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.