Esp32-joystick2trainer
RobertoD91·esp32-joystick2trainer·hardware/kicad/j2t-module.kicad_pcb
About the Esp32-joystick2trainer PCB
Esp32-joystick2trainer is an open source ESP32 PCB design by RobertoD91, published on GitHub under the MIT license. It is a 2-layer board measuring 22 × 62 mm, with 61 components from 39 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8, from the ESP32 family. Other key parts include the TPS54202DDCR, AP2112K-3.3TRG1 and CH340C. By type, the board carries 21 resistors, 16 capacitors, 5 transistors, 5 connectors, 5 diodes and 4 ICs.
It belongs with the iot & wireless, power & battery and rf & radio designs in this gallery.
From the project
A 22 x 62 mm two-layer board that turns the firmware into a module for the external module bay of an EdgeTX radio (TX16S and similar). It carries an ESP32-S3-WROOM-1, a USB-A host port for the joystick, a USB-C console/flashing port, a 2S-to-5 V buck converter and the bay connect
A 22 x 62 mm two-layer board that turns the firmware into a module for the external module bay of an EdgeTX radio (TX16S and similar). It carries an ESP32-S3-WROOM-1, a USB-A host port for the joystick, a USB-C console/flashing port, a 2S-to-5 V buck converter and the bay connector. Everything in this directory was generated from one Python description (scripts/design.py) with KiCad 7: schematic, PCB, routing, fabrication outputs, BOM and the printable case.

Main components on the Esp32-joystick2trainer
Esp32-joystick2trainer bill of materials (BOM)
61 components, 39 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS54202DDCR TPS54202 | SOT-23-6 | U1 |
| 1 | AP2112K-3.3TRG1 AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | ESP32-S3-WROOM-1-N8 | ESP32-S3-WROOM-1 | U3 |
| 1 | CH340C | SOIC-16_3.9x9.9mm_P1.27mm | U4 |
| 1 | AO3407A | SOT-23 | Q1 |
| 1 | AO3401A | SOT-23 | Q5 |
| 1 | 2N7002W | SOT-323_SC-70 | Q6 |
| 2 | BC847W | SOT-323_SC-70 | Q7, Q8 |
| 1 | Molex 67643-0910 or equivalent right-angle USB-A receptacle USB-A joystick | USB_A_Molex_67643_Horizontal | J1 |
| 1 | HRO TYPE-C-31-M-12 USB-C console | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 1 | AUX | PinHeader_1x03_P2.54mm_Vertical_SMD_Pin1Left | J3 |
| 1 | 1.27 mm pitch 1x4 pin header (or solder the display cable directly) I2C OLED | PinHeader_1x04_P1.27mm_Vertical | J4 |
| 1 | 2.54 mm right-angle header, long pins JR bay | PinHeader_1x05_P2.54mm_Horizontal | J5 |
| 1 | 1206L110 1.1A hold | Fuse_1206_3216Metric | F1 |
| 1 | 1206L075 0.75A hold | Fuse_1206_3216Metric | F2 |
| 1 | KMR221GLFS RESET | SW_Push_1P1T_NO_CK_KMR2 | SW1 |
| 1 | KMR221GLFS BOOT | SW_Push_1P1T_NO_CK_KMR2 | SW2 |
| 2 | USBLC6-2SC6 | SOT-23-6 | D2, D4 |
| 1 | green | LED_0603_1608Metric | D5 |
| 1 | red | LED_0603_1608Metric | D6 |
Show 19 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | B5819W | D_SOD-123 | D7 |
| 1 | SWPA5040S100MT 10uH 2.3A | L_Sunlord_SWPA5040S | L1 |
| 2 | 10uF 25V | C_0805_2012Metric | C1, C2 |
| 1 | 100nF 50V | C_0402_1005Metric | C3 |
| 4 | 100NF 100nF | C_0402_1005Metric | C4, C13, C15, C16 |
| 2 | 22uF 10V | C_0805_2012Metric | C5, C7 |
| 1 | 75PF 75pF | C_0402_1005Metric | C6 |
| 2 | 47uF 10V | C_1210_3225Metric | C8, C9 |
| 3 | 1UF 1uF | C_0402_1005Metric | C10, C11, C14 |
| 1 | 10uF 6.3V | C_0402_1005Metric | C12 |
| 4 | 100K 100k | R_0402_1005Metric | R1, R7, R8, R22 |
| 1 | 13.3K 13.3k | R_0402_1005Metric | R2 |
| 2 | 10K 10k | R_0402_1005Metric | R10, R11 |
| 2 | 12K 12k | R_0402_1005Metric | R12, R13 |
| 2 | 5.1K 5.1k | R_0402_1005Metric | R14, R15 |
| 6 | 1k | R_0402_1005Metric | R16, R17, R18, R20, R21, R24 |
| 1 | 22K 22k | R_0402_1005Metric | R23 |
| 1 | 2.2K 2.2k | R_0402_1005Metric | R25 |
| 2 | 4.7K 4.7k | R_0402_1005Metric | R26, R27 |
Esp32-joystick2trainer design files
The KiCad project lives in the RobertoD91/esp32-joystick2trainer repository on GitHub; these links point at the commit this page was built from.
Esp32-joystick2trainer: common questions
What microcontroller does the Esp32-joystick2trainer use?
The Esp32-joystick2trainer is built around the ESP32-S3-WROOM-1-N8, from the ESP32 family.
How big is the Esp32-joystick2trainer PCB?
The Esp32-joystick2trainer measures 22 × 62 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-joystick2trainer?
61 components, from 39 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32-joystick2trainer design files?
From the RobertoD91/esp32-joystick2trainer repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32-joystick2trainer design in my own project?
Yes, under the terms of its MIT license, which RobertoD91 chose for the repository.
Can I test firmware for the Esp32-joystick2trainer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k