30 open source boards using the TPS54202DDCR
Real designs built with the TPS54202DDCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
EuroPlatvorm
nanassound
21.7 × 89.8 mm34 parts4LNo license27Nrf52840 dimmer rgbw
vke
27.6 × 51.8 mm36 parts2LNo license8STM32
Hvsd-3ch
ExcessiveOverkill
109 × 231.4 mm457 parts4LNo license3STM32
UniversalFluxInterface
Axel051171
110 × 97 mm173 parts4LMIT3ESP32
Esp32-joystick2trainer
RobertoD91
22 × 62 mm61 parts2LMIT3Cluster2HDMI
vkar9898
128 × 55 mm94 parts4LMIT2ESP32
Esp32Tap - ESP32-S3 Precor serial bus tap
scottmsilver
95 × 58 mm76 parts4LNo license2ESP8266
3ChannelCCdriver
wszeto9
49 × 49 mm58 parts2LNo license2ESP32
ESP32-Small-SRWLED
wszeto9
19.6 × 20.3 mm35 parts4LNo license2STM32
MidiLedController hw
cracked-machine
99.8 × 100.1 mm138 parts2LNo license1STM32
Factory in a box
klaus-liebler
188 × 65 mm264 parts4LNo license0ESP32
Solar
DinosaurPotato534
149.6 × 65 mm201 parts2LNo license0Microchip SAM
D lev io
wormyrocks
125 × 50.1 mm115 parts4LNo license0Camera-Cooler
lukaslibar
45 × 75 mm106 parts4LCustom license0AVR/Arduino
Custom PSU
GodOfStrategy
99.6 × 73.1 mm105 parts2LNo license0ESP32
SmartKnob
aryanthomare
54 × 54 mm65 parts4LNo license0ESP32
MitsubishiSC
loozhengyuan
50 × 43 mm60 parts6LMIT0STM32
Ggsmdriver
gustavgaston
55 × 45 mm59 parts4LNo license0Powermod lt8645s
Slenderman00
27 × 18 mm20 parts4LNo license0Buck5v
Karthikeya2005
45 × 35 mm16 parts2LMIT0- schematic only · 88 partsSTM32
ReefVolt PlugControl — 2ch AC heater carrier
blueacro
88 parts4LCERN-OHL-P-2.00 ESP8266
3ChannelCCdriver panelized
wszeto9
100 × 100 mm58 parts2LNo license2ESP32
ESP32-Small-SRWLED panelization
wszeto9
41.7 × 43.1 mm35 parts4LNo license2AVR/Arduino
PID Board SMT
AaronDoubert
100 × 100 mm184 parts2LNo license0STM32
Flight controller
DinosaurPotato534
149 × 65 mm155 parts2LNo license0- schematic only · 81 partsESP32
ReefVolt SensorBuddy
blueacro
81 parts4LCERN-OHL-P-2.00 - schematic only · 49 partsSTM32
ReefVolt DryContact — 4ch Form-C carrier
blueacro
49 parts4LCERN-OHL-P-2.00 ESP32
SensactUp4
klaus-liebler
70 × 70 mm145 parts2LApache-2.04ESP32
Esp rgb driver
smkent
66 × 32 mm63 parts2LCC-BY-SA-4.00ESP32
Esp-3dp
smkent
66 × 32 mm53 parts2LCC-BY-SA-4.00
How designs wire the TPS54202DDCR
Read from the KiCad layouts of 23 open source designs, one per repository: what each pin of the TPS54202DDCR connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 22 of 23 designs, most often 15 µH (then 10 µH).
- The VIN pin has a decoupling capacitor on 22 of 23 designs, most often 10 µF (then 100 nF).
- The SW pin has a series capacitor on 21 of 23 designs, most often 100 nF (then 402 nF).
- The BOOT pin has a series capacitor on 21 of 23 designs, most often 100 nF (then 402 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 96% | — |
| SWpin 2 | Connected to: Signal 100% |
|
| VINpin 3 | Connected to: 12V 74% · a signal 26% |
|
| FBpin 4 | Connected to: Signal 100% |
|
| ENpin 5 | Connected to: Not connected 65% · a signal 35% | — |
| BOOTpin 6 | Connected to: Signal 96% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EuroPlatvorm by nanassound, Nrf52840 dimmer rgbw by vke, SensactUp4 by klaus-liebler and UniversalFluxInterface by Axel051171.
The TPS54202DDCR in open source designs
The gallery holds 30 open source boards using the TPS54202DDCR from 24 GitHub repositories; a typical one measures about 66 × 58 mm and carries around 71 components.
57% use four copper layers or more, and 37% carry an open source license.
The most starred is EuroPlatvorm by nanassound.
Parts used alongside the TPS54202DDCR
Microcontrollers on boards using the TPS54202DDCR
What boards using the TPS54202DDCR are built for
TPS54202DDCR: common questions
Where can I find a TPS54202DDCR reference design?
Each of the 30 boards on this page is a real design using the TPS54202DDCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS54202DDCR SW pin connected?
The SW pin has a inductor on 22 of 23 designs, most often 15 µH (then 10 µH). Counted from the KiCad layouts of 23 open source designs using the TPS54202DDCR.
What decoupling capacitors do designs use on the TPS54202DDCR VIN pin?
The VIN pin has a decoupling capacitor on 22 of 23 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 23 open source designs using the TPS54202DDCR.
How is the TPS54202DDCR BOOT pin connected?
The BOOT pin has a series capacitor on 21 of 23 designs, most often 100 nF (then 402 nF). Counted from the KiCad layouts of 23 open source designs using the TPS54202DDCR.
What parts are used alongside the TPS54202DDCR?
The USBLC6-2SC6, AP2112K-3.3TRG1, AMS1117-3.3, ESP32-S3-MINI-1-N8 and ESP32-S3-WROOM-1-N8 appear in the most repositories here.
Which microcontrollers do boards using the TPS54202DDCR use?
Most are built on ESP32 (12), STM32 (8), AVR/Arduino (2) and ESP8266 (2).
How big is a typical board using the TPS54202DDCR?
The median is 66 × 58 mm, and 43% are two-layer designs.
What is the most popular open source board using the TPS54202DDCR?
By GitHub stars, EuroPlatvorm by nanassound, with 27 stars.
Can I simulate one of these boards using the TPS54202DDCR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.