Subira
rodneyosodo·subira·kicad/subira.kicad_pcb
About the Subira PCB
Subira is an open source ESP32 PCB design by rodneyosodo, published on GitHub under the MIT license. It is a 2-layer board measuring 40 × 40 mm, with 37 components from 15 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AMS1117-3.3, BMI270 and LSM9DS1. By type, the board carries 19 capacitors, 9 resistors, 4 ICs, 2 switches, 2 diodes and 1 connector.
It belongs with the sensors designs in this gallery.
Main components on the Subira
Subira bill of materials (BOM)
37 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | BMI270 | BMI270_BOS-M | U3 |
| 1 | LSM9DS1 | LGA-24L_3x3.5mm_P0.43mm | U4 |
| 1 | USB_C_RECEPTACLE_USB2.0_14P USB_C_Receptacle_USB2.0_14P | USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
| 2 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 1 | LED | LED_0603_1608Metric | D1 |
| 1 | WS2812B-2020 | LED_WS2812B-2020_PLCC4_2.0x2.0mm | D2 |
| 2 | 1UF 1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2 |
| 7 | 10UF 10uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4, C6, C7, C9, C11, C18 |
| 9 | 0.1UF 0.1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C5, C8, C10, C12, C14, C15, C16, C17 +1 |
| 1 | 10nF (±10%) 16V | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13 |
| 2 | 10K | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 6 | 5.1K | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4, R6, R7, R8, R9 |
| 1 | 62 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5 |
Subira design files
The KiCad project lives in the rodneyosodo/subira repository on GitHub; these links point at the commit this page was built from.
- Layoutkicad/subira.kicad_pcb
- Schematickicad/subira.kicad_sch
- BOMkicad/production/bom.csv
Subira: common questions
What microcontroller does the Subira use?
The Subira is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Subira PCB?
The Subira measures 40 × 40 mm, has 2 copper layers and is 1 mm thick.
How many components are on the Subira?
37 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Subira design files?
From the rodneyosodo/subira repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Subira design in my own project?
Yes, under the terms of its MIT license, which rodneyosodo chose for the repository.
Can I test firmware for the Subira without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k