Controller
roy-rishi·lithophane-lightbox·ecad/controller/controller.kicad_pcb
About the Controller PCB
Controller is an open source ESP32 PCB design by roy-rishi, published on GitHub. It is a 2-layer board measuring 48 × 30 mm, with 24 components from 17 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the AMS1117-3.3, SN74LVC1T45DBVR and USBLC6-2SC6. By type, the board carries 6 capacitors, 6 resistors, 4 ICs, 3 switches, 2 diodes and 1 connector.
Main components on the Controller
Controller bill of materials (BOM)
24 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N16R8 ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | SN74LVC1T45DBVR SN74LVC1T45DBV | SOT-23-6_Handsoldering | U3 |
| 1 | USBLC6-2SC6 | SOT-23-6_Handsoldering | U4 |
| 1 | TYPE-C 6PLTH6.8-DJ USB_C_Receptacle_PowerOnly_6P | usb-c-vertical-smd | J2 |
| 1 | B3B-XH-A(LF)(SN) Conn_01x03 | JST_XH_B3B-XH-AM_1x03_P2.50mm_Vertical | LEDS1 |
| 1 | HX PH254-01-03-Z-L11.5 pcb pin header Conn_01x03 | PinHeader_1x03_P2.54mm_Vertical | PRGM1 |
| 3 | TS-1088-AR02016 SW | SW_SPST_TS-1088-xR020 | SW1, SW2, SW3 |
| 1 | SMAJ5.0CA | D_SMA | D1 |
| 1 | XL-2012SURC LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | CL21B105KBFNNNE 1uF | C_0805_2012Metric | C2 |
| 1 | GRM21BR61E226ME44L 22uF | C_0805_2012Metric | C3 |
| 3 | CL21B104KBCNNNC 0.1uF | C_0805_2012Metric | C4, C5, C7 |
| 1 | CL21A106KAYNNNE 10uF | C_0805_2012Metric | C9 |
| 3 | FRC0805F1002TS 10kΩ | R_0805_2012Metric | R1, R4, R5 |
| 2 | RC0805FR-075K1L 5.1kΩ | R_0805_2012Metric | R2, R3 |
| 1 | ARG05FTC0500 50Ω | R_0805_2012Metric | R6 |
Controller design files
The KiCad project lives in the roy-rishi/lithophane-lightbox repository on GitHub; these links point at the commit this page was built from.
Controller: common questions
What microcontroller does the Controller use?
The Controller is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.
How big is the Controller PCB?
The Controller measures 48 × 30 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Controller?
24 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Controller design files?
From the roy-rishi/lithophane-lightbox repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Controller design in my own project?
The repository has no license, so all rights stay with roy-rishi. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in lithophane-lightbox
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k