Arm

SHC-ASTRA·arm-electrical·Arm/Arm.kicad_pcb

Arm PCB layout, top view — open source ESP32 board by SHC-ASTRA

About the Arm PCB

Arm is an open source ESP32 PCB design by SHC-ASTRA, published on GitHub under the AGPL-3.0 license. It is a 2-layer board measuring 97 × 107 mm, with 50 components from 27 distinct parts.

Its main chip is the esp32_devkit_v1_doit, from the ESP32 family. Other key parts include the TJA1051T and RASPBERRY_PI_4B_4GB. By type, the board carries 16 resistors, 13 connectors, 8 ICs, 7 capacitors, 5 diodes and 1 module.

From the project

KiCAD files for Socket and Digit

Includes the KiCAD files for the Socket and Digit PCBs; Socket is located at the base of Arm and controls the Arm's main joints, Digit is located at the end of Arm and controls Wrist and End Effector.

Main components on the Arm

Arm bill of materials (BOM)

50 components, 27 distinct parts.

QtyPartRefs
1
~
U1
1
~
U2
1
~
U3
2
TJA1051T
U4, U5
2
~
U6, U8
1
RASPBERRY_PI_4B_4GB
U7
1
Fan
M1
1
Encoder Bundle
J2
1
CAN IN
J3
1
5V Swtich Power
J4
1
Power IN XT60 M
J5
4
SparkMAX XT60 F
J6, J10, J12, J13
1
Power OUT XT60 F
J7
1
Lynx
J8
1
CANBUS
J9
1
CAN OUT
J11
1
Encoder 0
J14
4
LED
D1, D2, D3, D4
1
Inolux_IN-PI554FCH
D5
2
4.7 nf
C1, C2
Show 7 more
QtyPartRefs
2
1 uF
C3, C4
3
0.1 uF
C5, C6, C7
6
10K ohm
R1, R2, R3, R4, R6, R16
1
3.32K Ohm
R5
1
2.21K ohm
R7
4
3.8K Ohm
R8, R9, R10, R11
4
60Ω
R12, R13, R14, R15

Arm design files

The KiCad project lives in the SHC-ASTRA/arm-electrical repository on GitHub; these links point at the commit this page was built from.

Arm: common questions

What microcontroller does the Arm use?

The Arm is built around the esp32_devkit_v1_doit, from the ESP32 family.

How big is the Arm PCB?

The Arm measures 97 × 107 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Arm?

50 components, from 27 distinct parts. The full bill of materials is listed on this page.

Where can I download the Arm design files?

From the SHC-ASTRA/arm-electrical repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Arm design in my own project?

Yes, under the terms of its AGPL-3.0 license, which SHC-ASTRA chose for the repository.

Can I test firmware for the Arm without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in arm-electrical

Similar boards