33 open source boards using the TJA1051T
Real designs built with the TJA1051T, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
Wifi2can
zhangxuhong1024
65 × 40 mm55 parts2LNo license9STM32
Motor42
zhbi98
42 × 42 mm82 parts4LMIT8ESP32
ESp32-DEVKIT-DATALOGGER
Zektopic
262.2 × 139.3 mm84 parts2LNo license7STM32
Motor35
zhbi98
35 × 35 mm71 parts4LMIT2AVR/Arduino
EngineDataLogger-FrontControls
techie66
95 × 95 mm130 parts2LGPL-2.01STM32
MasterModule
dmitry131131
50 × 70 mm22 parts2LNo license1STM32
Test Projekt
Siegmundshof93
86.2 × 91.9 mm147 parts2LNo license0STM32
Motor-Driver-V2
anshinx
132.5 × 118.2 mm117 parts4LNo license0ESP32
Workcross-ReverseCam
db8fs
112 × 64 mm70 parts2LGPL-3.00STM32
PneumaticPaddleShifting
DallasFormulaRacing
156.6 × 143.1 mm52 parts4LNo license0STM32
Atlas load cell
aesirkth
60 × 50 mm48 parts2LNo license0Cyberboard usb
cybergear-robotics
55 × 55 mm40 parts4LMIT0AVR/Arduino
Can atmega layout-2025-07-01
Zwackelmann
111 × 150 mm39 parts2LNo license0ESP32
Control
kramerbastian
71 × 60 mm28 parts2LNo license0Raspberry Pi
Headunit pi4
Jimbo145
193.7 × 97.1 mm19 parts2LNo license0Tja1051-breakout
11philip22
32.3 × 15.7 mm10 parts2LNo license0- schematic only · 53 partsSTM32
JB-Micro-Wheeled leg-Robot
baijiazheng
53 partsNo license0 ESP32
ESP32-S3-MINI-DEVKIT-DATALOGGER
Zektopic
262.2 × 139.3 mm82 parts2LNo license7AVR/Arduino
Laser Stripe Sensor
lindamao-waterloop
68.6 × 53.3 mm33 parts2LNo license2ESP32
Arm
SHC-ASTRA
97 × 107 mm50 parts2LAGPL-3.00AVR/Arduino
Temp sensor
Zwackelmann
52.5 × 52.5 mm36 parts2LNo license0AVR/Arduino
BrakeActuator
lindamao-waterloop
38.1 × 25.4 mm26 parts2LNo license2STM32
Stm32f429z
WilliamLim781
153 × 114.3 mm79 parts4LNo license1AVR/Arduino
Can atmega
Zwackelmann
37 × 48 mm26 parts2LNo license0AVR/Arduino
Torchic
lindamao-waterloop
42.2 × 25.4 mm21 parts2LNo license2AVR/Arduino
VCU V3.3
HKUST-Red-Bird-Racing-EVRT
114 × 95 mm145 parts2LNo license0AVR/Arduino
Optical Ring Encoder
lindamao-waterloop
46.4 × 25.6 mm20 parts2LNo license2ESP32
SSRU v3.3
HKUST-Red-Bird-Racing-EVRT
95 × 78 mm66 parts2LNo license3AVR/Arduino
Delibird
lindamao-waterloop
38.1 × 25.4 mm18 parts2LNo license2AVR/Arduino
Psyduck
lindamao-waterloop
38.1 × 25.4 mm15 parts2LNo license2AVR/Arduino
SSRU v4.0
HKUST-Red-Bird-Racing-EVRT
95 × 78 mm68 parts2LNo license0ESP32
ESP32 CAN TEST
SamsonChau
45.7 × 45.8 mm39 parts2LNo license0Poncho CAN
brengi
85.7 × 79.6 mm37 parts2LNo license7
How designs wire the TJA1051T
Read from the KiCad layouts of 23 open source designs, one per repository: what each pin of the TJA1051T connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 14 of 23 designs, most often 100 nF (then 10 µF).
- The CANL pin has a series resistor on 13 of 23 designs, most often 120 Ω (then 62 Ω).
- The CANH pin has a series resistor on 12 of 23 designs, most often 120 Ω (then 62 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| VCCpin 3 | Connected to: 5V 100% |
|
| NCpin 5 | Connected to: Not connected 87% | — |
| CANLpin 6 | Connected to: A connector 91% |
|
| CANHpin 7 | Connected to: A connector 96% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Wifi2can by zhangxuhong1024, Motor42 by zhbi98, Poncho CAN by brengi and ESp32-DEVKIT-DATALOGGER by Zektopic.
The TJA1051T in open source designs
The gallery holds 33 open source boards using the TJA1051T from 24 GitHub repositories; a typical one measures about 69.8 × 62 mm and carries around 48 components.
81% are two-layer designs, the rest use four layers or more, and 18% carry an open source license.
The most starred is Wifi2can by zhangxuhong1024.
Parts used alongside the TJA1051T
Microcontrollers on boards using the TJA1051T
What boards using the TJA1051T are built for
TJA1051T: common questions
Where can I find a TJA1051T reference design?
Each of the 33 boards on this page is a real design using the TJA1051T. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TJA1051T VCC pin?
The VCC pin has a decoupling capacitor on 14 of 23 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 23 open source designs using the TJA1051T.
What resistor goes on the TJA1051T CANL pin?
The CANL pin has a series resistor on 13 of 23 designs, most often 120 Ω (then 62 Ω). Counted from the KiCad layouts of 23 open source designs using the TJA1051T.
What resistor goes on the TJA1051T CANH pin?
The CANH pin has a series resistor on 12 of 23 designs, most often 120 Ω (then 62 Ω). Counted from the KiCad layouts of 23 open source designs using the TJA1051T.
What parts are used alongside the TJA1051T?
The AMS1117-3.3, MCP2515-xSO, ATmega328P-A, CH340C and ESP32-S3-WROOM-1 appear in the most repositories here.
Which microcontrollers do boards using the TJA1051T use?
Most are built on AVR/Arduino (12), STM32 (9), ESP32 (7) and ESP8266 (1).
How big is a typical board using the TJA1051T?
The median is 69.8 × 62 mm, and 81% are two-layer designs.
What is the most popular open source board using the TJA1051T?
By GitHub stars, Wifi2can by zhangxuhong1024, with 9 stars.
Can I simulate one of these boards using the TJA1051T before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.