Flight controller

someonelse20·flight-controller·hardware/flight-controller.kicad_pcb

Flight controller PCB layout, top view — open source STM32 board by someonelse20

About the Flight controller PCB

Flight controller is an open source STM32 PCB design by someonelse20, published on GitHub. It is a 4-layer board measuring 70 × 70 mm, with 116 components from 52 distinct parts.

Its main chip is the STM32H723VGTX, from the STM32 family. Other key parts include the BMP384, LSM6DSOTR, MMC5983MA, MAX-M10S and TPS2121RUXR. By type, the board carries 39 capacitors, 34 resistors, 23 connectors, 7 ICs, 4 diodes and 2 crystals.

It belongs with the robotics & motion, rf & radio and power & battery designs in this gallery.

From the project

A custom flight controller with IMU sensors for orientation, a GPS module, a Micro SD card slot, and support for my LoRa Transceiver module for telemetry along with a custom flight controller algorithm. I built this for my project of creating a custom drone from scratch.

Flight controller, from the project README
From the project README

Main components on the Flight controller

Flight controller bill of materials (BOM)

116 components, 52 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
BMP384
U1
1
LSM6DSOTR
LSM6DSOX
U2
1
MMC5983MA
U3
1
MAX-M10S
U4
1
TPS2121RUXR
U5
1
AP62300TWU
U6
1
STM32H723VGTX
STM32H723VGTx
U7
1
Q13FC13500004
Y1
1
X322525MOB4SI
Y2
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J1
1
CONN_01X02
Conn_01x02
J2
1
Conn_Coaxial
J3
4
CONN_01X04
Conn_01x04
J4, J6, J8, J17
6
SCREW_TERMINAL_01X02
Screw_Terminal_01x02
J5, J7, J9, J10, J16, J18
1
MICRO_SD_CARD_DET_HIROSE_DM3AT
Micro_SD_Card_Det_Hirose_DM3AT
J11
4
CONN_01X03
Conn_01x03
J12, J13, J14, J15
5
CONN_01X02
Conn_01x02
J19, J20, J21, J22, J23
3
SW_Push
BOOT1, RESET1, SET1
1
MS621FE-FL11E
BT1
1
PKMCS0909E4000-R1
BZ1
Show 32 more
QtyPartRefs
1
D_Schottky
D1
3
LED
D2, D3, D4
1
FerriteBead
FB1
1
3.3UH
3.3uH
L1
4
1UF
1uF
C1, C8, C19, C21
15
100NF
100nF
C2, C3, C4, C6, C7, C11, C18, C20 +7
2
10UF
10uF
C5, C16
2
18PF
18pF
C9, C14
2
15PF
15pF
C10, C13
1
1UF
1uF
C12
2
2.2UF
2.2uF
C15, C17
1
10PF
10pF
C23
2
22UF
22uF
C26, C28
1
4.7UF
4.7uF
C31
6
10UF
10uF
C32, C33, C34, C35, C36, C37
1
22UF
22uF
C38
2
5.1K
R1, R2
4
1K
R3, R13, R14, R15
1
23.7K
R4
5
5K
R5, R7, R9, R11, R30
1
60K
62K
R6
1
5K
R8
1
30K
R10
1
50K
51K
R12
8
10K
R16, R18, R22, R23, R24, R25, R26, R27
1
47
R17
1
33.2K
R19
2
27
R20, R21
1
100
R28
1
13.2K
R29
2
1.2K
R31, R32
2
4.7K
R33, R34

Flight controller design files

The KiCad project lives in the someonelse20/flight-controller repository on GitHub; these links point at the commit this page was built from.

Flight controller: common questions

What microcontroller does the Flight controller use?

The Flight controller is built around the STM32H723VGTX, from the STM32 family.

How big is the Flight controller PCB?

The Flight controller measures 70 × 70 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Flight controller?

116 components, from 52 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Flight controller design files?

From the someonelse20/flight-controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Flight controller design in my own project?

The repository has no license, so all rights stay with someonelse20. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Flight controller without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards