Osmo pocket esp32-gimbal
SREESAIARJUN·osmo-pocket-esp32-gimbal·kicad/osmo-pocket-esp32-gimbal.kicad_pcb
About the Osmo pocket esp32-gimbal PCB
Osmo pocket esp32-gimbal is an open source ESP32 PCB design by SREESAIARJUN, published on GitHub. It is a 4-layer board measuring 26 × 85 mm, with 53 components from 35 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8R8, from the ESP32 family. Other key parts include the TCA9548APWR, AS5600-ASOM, TPS563201DDCR and ICM-42688-P. By type, the board carries 18 capacitors, 15 resistors, 7 ICs, 7 test points, 4 connectors and 2 inductors.
It belongs with the sensors designs in this gallery.
From the project
3-Axis Handheld Gimbal (DJI Osmo Pocket Form Factor): ESP32-S3 FOC motor control, parametric CAD, KiCad 8 hardware, and real dynamic physics simulator
Autonomous Engineering Release — Revision 7.0 / 150 Powered by ESP32-S3 Dual-Core LX7 @ 240MHz, SimpleFOC Field-Oriented Control, and Real Physics Simulation.
At 8 MHz that is about 22 µs of bus time per record, under 5 % of SPI2 for both IMUs at 1 kHz. - Fault handling. - Overflow: sets the resync flag, so dt is not trusted across the gap. - Impossible count: the FIFO is flushed. - Header mismatch: the FIFO is flushed and resync is flagged. A record header with the "empty" bit set inside the latched count also counts as lost alignment (see review fix R2). - Invalid-sample markers (0x8000 in…
Main components on the Osmo pocket esp32-gimbal
Osmo pocket esp32-gimbal bill of materials (BOM)
53 components, 35 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N8R8 | ESP32-S3-WROOM-1 | U1 |
| 1 | TCA9548APWR | TSSOP-24_4.4x7.8mm_P0.65mm | U2 |
| 3 | AS5600-ASOM | SOIC-8_3.9x4.9mm_P1.27mm | U3, U4, U5 |
| 1 | TPS563201DDCR | SOT-23-6 | U6 |
| 1 | ICM-42688-P | LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | U7 |
| 1 | ENC_PAN (JST-SH 4p) | JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J1 |
| 1 | ENC_ROLL (JST-SH 4p) | JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J2 |
| 1 | ENC_PITCH (JST-SH 4p) | JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J3 |
| 1 | S2B-PH-SM4-TB BATT 2S (JST-PH 2p) | JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_Horizontal | J4 |
| 1 | +5V | TestPoint_Pad_D1.0mm | TP1 |
| 1 | +3V3 | TestPoint_Pad_D1.0mm | TP2 |
| 1 | GND | TestPoint_Pad_D1.0mm | TP3 |
| 1 | IMU_SPI_SCK | TestPoint_Pad_D1.0mm | TP4 |
| 1 | IMU_SPI_MOSI | TestPoint_Pad_D1.0mm | TP5 |
| 1 | IMU_SPI_MISO | TestPoint_Pad_D1.0mm | TP6 |
| 1 | IMU_CS_HANDLE | TestPoint_Pad_D1.0mm | TP7 |
| 1 | BLM15AG601SN1D 600R@100MHz | L_0402_1005Metric | FB1 |
| 1 | XGL4030-332MEC 3.3uH 5A | L_Coilcraft_XGL4030 | L1 |
| 4 | 1uF | C_0402_1005Metric | C1, C6, C8, C10 |
| 1 | 10uF | C_0603_1608Metric | C2 |
Show 15 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 5 | 100nF | C_0402_1005Metric | C3, C4, C5, C7, C9 |
| 1 | 10uF 25V X7R | C_0805_2012Metric | C11 |
| 1 | 100nF 25V X7R | C_0402_1005Metric | C12 |
| 1 | 100nF 16V | C_0402_1005Metric | C13 |
| 2 | 22uF 10V X5R | C_0805_2012Metric | C14, C15 |
| 1 | 1uF 10V X5R | C_0402_1005Metric | C16 |
| 2 | 100nF 10V X7R | C_0402_1005Metric | C17, C18 |
| 2 | 10k | R_0402_1005Metric | R1, R2 |
| 2 | 2.2k | R_0402_1005Metric | R3, R4 |
| 6 | 4.7k | R_0402_1005Metric | R5, R6, R7, R8, R9, R10 |
| 1 | 54.9k 1% | R_0402_1005Metric | R11 |
| 1 | 10k 1% | R_0402_1005Metric | R12 |
| 1 | 100k 1% | R_0402_1005Metric | R13 |
| 1 | 24.9k 1% | R_0402_1005Metric | R14 |
| 1 | 33R | R_0402_1005Metric | R15 |
Osmo pocket esp32-gimbal design files
The KiCad project lives in the SREESAIARJUN/osmo-pocket-esp32-gimbal repository on GitHub; these links point at the commit this page was built from.
Osmo pocket esp32-gimbal: common questions
What microcontroller does the Osmo pocket esp32-gimbal use?
The Osmo pocket esp32-gimbal is built around the ESP32-S3-WROOM-1-N8R8, from the ESP32 family.
How big is the Osmo pocket esp32-gimbal PCB?
The Osmo pocket esp32-gimbal measures 26 × 85 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Osmo pocket esp32-gimbal?
53 components, from 35 distinct parts. The full bill of materials is listed on this page.
Where can I download the Osmo pocket esp32-gimbal design files?
From the SREESAIARJUN/osmo-pocket-esp32-gimbal repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Osmo pocket esp32-gimbal design in my own project?
The repository has no license, so all rights stay with SREESAIARJUN. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Osmo pocket esp32-gimbal without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k