Starbie
starharish0210-afk·starbie-pcb
About the Starbie PCB
Starbie is an open source ESP32 PCB design by starharish0210-afk, published on GitHub. It is a 2-layer board measuring 109 × 103.8 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
It belongs with the sensors and displays & leds designs in this gallery.
From the project
a cute little desk buddy, to interact and helpful
A tiny motion-controlled desk pet on a star-shaped PCB. A little creature wanders around a 128x64 OLED, and you play with it by pressing two key switches, tilting the board and shaking it. A temperature and humidity sensor shows the room's conditions on a stats screen.
Starbie is my version of the Half Life starter project. The board holds a XIAO ESP32-C3 that runs the pet program, an OLED that shows it, an MPU6050 that senses tilt and shake, a DHT11 that measures temperature and humidity, and two Cherry MX-style key switches for input. The firmware is the single-file Arduino sketch from the…
Main components on the Starbie
Starbie bill of materials (BOM)
7 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C6-DIP | U1 |
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U2 |
| 1 | Conn_01x04_Pin | Display_128x64_096_I2C | J1 |
| 1 | Conn_01x08_Pin | MPU6050_Module | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
Starbie design files
The KiCad project lives in the starharish0210-afk/starbie-pcb repository on GitHub; these links point at the commit this page was built from.
- Layoutkicad.kicad_pcb
- Schematickicad.kicad_sch
- BOMBOM.csv
Starbie: common questions
What microcontroller does the Starbie use?
The Starbie is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Starbie PCB?
The Starbie measures 109 × 103.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Starbie?
7 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Starbie design files?
From the starharish0210-afk/starbie-pcb repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Starbie design in my own project?
The repository has no license, so all rights stay with starharish0210-afk. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Starbie without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k