Esp32-lora environmental datalogger sink
SuryaTejaJakka14·esp32-lora-environmental-datalogger-sink·hardware/schematic/PCB.kicad_sch

About the Esp32-lora environmental datalogger sink PCB
Esp32-lora environmental datalogger sink is an open source AVR/Arduino PCB design by SuryaTejaJakka14, published on GitHub. It is a board, with 96 components from 48 distinct parts.
Its main chip is the ATmega328P-AU, from the AVR/Arduino family. Other key parts include the NCP170_TSTOP-5, MCP73832-2-OT, SX1262, AT45DB161D-SU and MCP79510. By type, the board carries 40 capacitors, 19 resistors, 11 ICs, 8 connectors, 3 inductors and 2 crystals.
It belongs with the rf & radio, sensors and iot & wireless designs in this gallery.
From the project
ESP32 firmware with a custom LoRa driver and KiCad PCB design for a low-power environmental sensor node built for long-range field telemetry.
Custom ESP-IDF firmware and KiCad-designed PCB for a low-power LoRa environmental sensor network. This repository contains the sink node firmware — the receiver that collects raw telemetry from a cluster of distributed logger nodes, tags and stores it locally, and periodically forwards it downstream in batches.
This sink node receives raw sensor data transmitted over LoRa by a cluster of distributed logger nodes in the field. Each incoming transmission is tagged with the originating device's name/ID and written to local storage. Rather than forwarding data immediately, the sink accumulates…
Main components on the Esp32-lora environmental datalogger sink
Esp32-lora environmental datalogger sink bill of materials (BOM)
96 components, 48 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | NCP170_TSTOP-5 | TSOT-23-5 | U1 |
| 1 | MCP73832-2-OT | SOT-23-5 | U2 |
| 1 | SX1262 | QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm_ThermalVias | U3 |
| 1 | AT45DB161D-SU | SOIC-8_5.275x5.275mm_P1.27mm | U4 |
| 1 | MCP79510 | MSOP-10_3x3mm_P0.5mm | U5 |
| 1 | RF_filter_0900FM15D0039 | 0900FM15D0039E | U6 |
| 1 | CG2179 | SC-70-6 | U7 |
| 1 | SHTC3 | AMS_QFN-4-1EP_2x2mm_P0.95mm_EP0.7x1.6mm | U8 |
| 1 | ATmega328P-AU | TQFP-32_7x7mm_P0.8mm | U10 |
| 1 | AP2171_DFN-6 | DFN-6-1EP_2x1.8mm_P0.5mm_EP1.2x1.6mm | U11 |
| 1 | MCP3208 | SOIC-16_3.9x9.9mm_P1.27mm | U12 |
| 1 | Crystal_GND24 | Crystal_SMD_EuroQuartz_X22-4Pin_2.5x2.0mm | Y1 |
| 1 | Crystal | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y2 |
| 2 | Conn_01x02_Male | JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_Horizontal | J1, J2 |
| 2 | Conn_01x01_Female | PinHeader_1x01_P2.54mm_Vertical | J3, J5 |
| 3 | Screw_Terminal_01x04 | TerminalBlock_MetzConnect_Type059_RT06304HBWC_1x04_P3.50mm_Horizontal | J7, J8, J10 |
| 1 | Conn_02x03_Odd_Even | PinHeader_2x03_P2.54mm_Vertical_SMD | J9 |
| 1 | Antenna_Chip | Chip_Antenna_0915AT43A0026E | AE1 |
| 1 | 3V | BatteryHolder_Keystone_3000_1x12mm | BT1 |
| 1 | Battery_Cell | battery_holder_halfAA1 | BT2 |
Show 28 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | Dummy_footprint | ESD-Logo_6.6x6mm_SilkScreen | G2, G4 |
| 1 | Dummy_footprint | OSHW-Logo2_9.8x8mm_SilkScreen | G3 |
| 3 | MountingHole | MountingHole_2.5mm | H1, H2, H3 |
| 1 | Jumper | SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
| 1 | Jumper_3_Open | SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mm | JP2 |
| 1 | SW_Push | SW_SPST_EVPBF | SW1 |
| 1 | LED | LED_0603_1608Metric | D2 |
| 1 | 47n | L_0402_1005Metric | L1 |
| 1 | 9.1n | L_0402_1005Metric | L2 |
| 1 | L | L_0805_2012Metric | L3 |
| 7 | 10u | C_0805_2012Metric | C1, C2, C9, C20, C23, C39, C50 |
| 5 | 1u | C_0603_1608Metric | C3, C6, C17, C28, C30 |
| 16 | 0.1u | C_0402_1005Metric | C4, C15, C19, C21, C22, C26, C27, C29 +8 |
| 1 | 470n | C_0402_1005Metric | C5 |
| 1 | 47p | C_0402_1005Metric | C7 |
| 1 | 47n | C_0402_1005Metric | C8 |
| 2 | 1n | C_0402_1005Metric | C10, C12 |
| 2 | 4.7u | C_0805_2012Metric | C11, C18 |
| 1 | 39p | C_0402_1005Metric | C13 |
| 2 | 3.3p | C_0402_1005Metric | C14, C16 |
| 2 | 10p | C_0402_1005Metric | C33, C34 |
| 5 | 1M | R_0402_1005Metric | R1, R12, R17, R18, R20 |
| 2 | 10k | R_0402_1005Metric | R2, R22 |
| 6 | 1k | R_0402_1005Metric | R4, R5, R6, R7, R8, R11 |
| 2 | 100 | R_0402_1005Metric | R9, R10 |
| 1 | 10M | R_0402_1005Metric | R15 |
| 2 | 4.7k | R_0402_1005Metric | R21, R23 |
| 1 | 200 | R_0402_1005Metric | R24 |
Esp32-lora environmental datalogger sink design files
The KiCad project lives in the SuryaTejaJakka14/esp32-lora-environmental-datalogger-sink repository on GitHub; these links point at the commit this page was built from.
- Schematichardware/schematic/PCB.kicad_sch
Esp32-lora environmental datalogger sink: common questions
What microcontroller does the Esp32-lora environmental datalogger sink use?
The Esp32-lora environmental datalogger sink is built around the ATmega328P-AU, from the AVR/Arduino family.
How many components are on the Esp32-lora environmental datalogger sink?
96 components, from 48 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32-lora environmental datalogger sink design files?
From the SuryaTejaJakka14/esp32-lora-environmental-datalogger-sink repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Esp32-lora environmental datalogger sink design in my own project?
The repository has no license, so all rights stay with SuryaTejaJakka14. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32-lora environmental datalogger sink without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k