36 open source boards using the SHTC3
Real designs built with the SHTC3, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Esp rust board
esp-rs
22.9 × 63.5 mm48 parts2LNo license648Smart sensor battery pack
FeatureNAB
23 × 56 mm30 parts2LCC-BY-NC-4.0215ESP32
ClimateSprinklerController
kbx81
217 × 108 mm189 parts2LNo license55Raspberry Pi
Ic880a backplane
dbrgn
93.9 × 83.8 mm34 parts2LTAPR-OHL-1.015ESP32
ESP32-C3-DevKit-RUST-1
swayerloren
22.9 × 63.5 mm48 parts2LMIT8ESP32
Plant133
chl33
59.2 × 41.9 mm56 parts4LMIT5ESP32
Soldered Inkplate 6 MOTION
SolderedElectronics
144.4 × 107.8 mm313 parts2LTAPR-OHL-1.04ESP32
ESP32-C3-DevKit-RUST-1
xutianq999
22.9 × 63.5 mm48 parts2LCERN-OHL-P-2.04ESP32
Dough133
chl33
69.9 × 44.5 mm59 parts4LMIT2ESP32
Garden133
chl33
71.1 × 39.4 mm54 parts4LMIT2ESP32
Lumi tubule
NemoAndrea
83.1 × 83.1 mm74 parts2LCERN-OHL-W-2.01ESP32
Garage133
chl33
97.8 × 39.4 mm52 parts4LMIT1ESP32
Room133
chl33
47.6 × 39.4 mm36 parts4LMIT1Riotee SensorShield
NessieCircuits
55.9 × 22.9 mm21 parts2LCERN-OHL-W-2.01ESP32
LoRa133
chl33
49.5 × 39.4 mm20 parts4LMIT1STM32
Plant monitor
PimentoFr
50 × 74 mm168 parts4LNo license0Nordic nRF
Ssense lte
fredriknk
113 × 25.1 mm105 parts4LMIT0Nordic nRF
Soilsense
fredriknk
90 × 21 mm62 parts4LMIT0Nordic nRF
Sensus hardware
klausen-tech
36.5 × 35 mm61 parts4LNo license0ESP32
Temp sensor
juniper-garden
48.2 × 24.9 mm55 parts2LGPL-3.00ESP32
Esp32c3
souptik-samanta
40.8 × 20 mm47 parts4LNo license0Nordic nRF
Pcb
UPM-SPV
0.7 × 0.7 mm40 parts4LCERN-OHL-S-2.00Nordic nRF
BSN-N54
Stachu1
34 × 34 mm33 parts4LNo license0ESP32
Bussysteme und-Sensorik-ESP32-Projekt
SFMonsun
111.7 × 63.8 mm32 parts4LNo license0- schematic only · 96 partsAVR/Arduino
Esp32-lora environmental datalogger sink
SuryaTejaJakka14
96 partsNo license0 RP2040/RP2350
Xterminal
lithiumice
33 × 33 mm67 parts2LNo license92RISC-V
CyberTastic
wrickert
88.1 × 44.6 mm60 parts2LNo license8ESP32
Soldered Inkplate 6 MOTION panel
SolderedElectronics
144.4 × 221.6 mm313 parts2LTAPR-OHL-1.04Nordic nRF
Soilsense RFtest
fredriknk
90 × 21 mm60 parts4LMIT0STM32
IoTSlave
SR-Madsen
43.7 × 41.6 mm50 parts4LNo license0ESP32
Temp sensor panel v2
juniper-garden
115 × 61 mm49 parts2LGPL-3.00BSN-C23
Stachu1
34 × 34 mm28 parts4LNo license0ESP32
Temp sensor panel
juniper-garden
188.7 × 147.5 mm40 parts2LGPL-3.00STM32
DefCon31 HeatIndex BadgeAddon
androda
39.1 × 90.6 mm19 parts2LCC-BY-NC-4.021Sensor stick
AirMQ
28 × 6.6 mm11 parts2LCERN-OHL-P-2.02Inkusense mini
maurer-lbb
8.3 × 8.6 mm7 parts2LCC-BY-SA-4.00
How designs wire the SHTC3
Read from the KiCad layouts of 30 open source designs, one per repository: what each pin of the SHTC3 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 28 of 30 designs, most often 100 nF (then 10 nF).
- The SCL pin has a pull-up to 3.3V on 24 of 30 designs, most often 10 kΩ (then 2.2 kΩ).
- The SDA pin has a pull-up to 3.3V on 24 of 30 designs, most often 10 kΩ (then 2.2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 3.3V 100% |
|
| SCLpin 2 | Connected to: The microcontroller 77%, a connector 27% |
|
| SDApin 3 | Connected to: The microcontroller 77%, a connector 27% |
|
| VSSpin 4 | Connected to: GND 100% | — |
| NCpin 5 | Connected to: Not connected 62% · GND 38% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Esp rust board by esp-rs, Smart sensor battery pack by FeatureNAB, Xterminal by lithiumice and ClimateSprinklerController by kbx81.
The SHTC3 in open source designs
The gallery holds 36 open source boards using the SHTC3 from 31 GitHub repositories; a typical one measures about 50 × 41.5 mm and carries around 50 components.
51% are two-layer designs, the rest use four layers or more, and 61% carry an open source license.
The most starred is Esp rust board by esp-rs.
Parts used alongside the SHTC3
Microcontrollers on boards using the SHTC3
What boards using the SHTC3 are built for
SHTC3: common questions
Where can I find a SHTC3 reference design?
Each of the 36 boards on this page is a real design using the SHTC3. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SHTC3 VDD pin?
The VDD pin has a decoupling capacitor on 28 of 30 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 30 open source designs using the SHTC3.
What pull-up resistor is used on the SHTC3 SCL pin?
The SCL pin has a pull-up to 3.3V on 24 of 30 designs, most often 10 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 30 open source designs using the SHTC3.
What pull-up resistor is used on the SHTC3 SDA pin?
The SDA pin has a pull-up to 3.3V on 24 of 30 designs, most often 10 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 30 open source designs using the SHTC3.
What parts are used alongside the SHTC3?
The ESP32-WROOM-32, AMS1117-3.3, ESP32-C3-MINI-1, MCP73831T-2ACI/OT and BME280 appear in the most repositories here.
Which microcontrollers do boards using the SHTC3 use?
Most are built on ESP32 (18), Nordic nRF (6), STM32 (3) and RP2040/RP2350 (1).
How big is a typical board using the SHTC3?
The median is 50 × 41.5 mm, and 51% are two-layer designs.
What is the most popular open source board using the SHTC3?
By GitHub stars, Esp rust board by esp-rs, with 648 stars.
Can I simulate one of these boards using the SHTC3 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.