Qnot
SushEdge·Qnot
About the Qnot PCB
Qnot is an open source STM32 PCB design by SushEdge, published on GitHub. It is a 8-layer board measuring 34 × 34 mm, with 211 components from 65 distinct parts.
Its main chip is the STM32F405RGTx, from the STM32 family. Other key parts include the TPS54560BDDA, AT7456, OUTLINE, RT9013-33GB and BMP280. By type, the board carries 85 resistors, 58 capacitors, 28 ICs, 20 connectors, 15 diodes and 2 crystals.
It belongs with the sensors, robotics & motion and power & battery designs in this gallery.
From the project
#blueprint #HackClub
All-in-One (AIO) circuit for quadcopter. STM32F405 is the main controller for FC and EFM8BB21 is the main controller for ESC. Screw hole dimension is 26x26 mm that compatible for almost tiny drone frame.
Everything about this board: Schematic, PCB gerber and BOM are free to distribute under open-source license for users.
This board use jumper to select 5V power source and to enable 3V3 power supply.
Main components on the Qnot
Qnot bill of materials (BOM)
211 components, 65 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | ~ | QFN-20-1EP_3x3mm_P0.5mm_EP1.8x1.8mm | U1, U2, U7, U8 |
| 1 | TPS54560BDDA | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm | U3 |
| 5 | ~ | QFN-24-1EP_4x4mm_P0.5mm_EP2.15x2.15mm | U4, U5, U9, U10, U29 |
| 1 | AT7456 | TSSOP-28-1EP_4.4x9.7mm_P0.65mm | U6 |
| 1 | OUTLINE | Board_Outline | U11 |
| 1 | RT9013-33GB | SOT65P210X110-6N | U12 |
| 1 | BMP280 | Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U13 |
| 1 | ~ | Texas_R-PDSO-G6 | U14 |
| 1 | STM32F405RGTx | LQFP-64_10x10mm_P0.5mm | U15 |
| 12 | ~ | SIZ200DT | U17, U18, U19, U20, U21, U22, U23, U24 +4 |
| 2 | 8Mhz | Crystal_SMD_2016-4Pin_2.0x1.6mm | Y1, Y2 |
| 1 | SPI | MountingPad_1x6 | J1 |
| 1 | Conn_02x04_Odd_Even | PinHeader_2x04_P1.27mm_Vertical_SMD | J2 |
| 1 | UART4 | MountingPad_1x4 | J4 |
| 1 | ST-LINK | STLINK_Port | J5 |
| 1 | RC | MountingPad_1x4 | J7 |
| 1 | UART6 | MountingPad_1x4 | J8 |
| 1 | OSD | MountingPad_1x4 | J9 |
| 1 | Conn_02x02_Odd_Even | PinHeader_2x02_P1.27mm_Vertical_SMD | J12 |
| 1 | UART1 | MountingPad_1x4 | J14 |
Show 45 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | UART3_I2C2 | MountingPad_1x4 | J15 |
| 4 | MOTOR | Hirose_DF13-03P-1.25DS_1x03_P1.25mm_Horizontal | J16, J17, J18, J19 |
| 1 | USB_A | USB_Micro-B_SMD | J20 |
| 4 | ESC_PROG | ESC_Program | J21, J23, J24, J25 |
| 1 | LED_BUZ | MountingPad_1x4 | J26 |
| 1 | VBAT+ | MoutingPad | H1 |
| 1 | VBAT- | MoutingPad | H2 |
| 1 | S6M_770mV/6A | D_SMA | D1 |
| 12 | BAT54 | D_SOD-323 | D2, D3, D6, D7, D8, D9, D12, D13 +4 |
| 1 | LED_RED | LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D5 |
| 1 | LED_BLUE | LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D18 |
| 1 | 10uH | Inductor | L1 |
| 2 | 4.7uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C19 |
| 4 | 100uF | C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C2, C3, C4, C10 |
| 1 | 11nF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C5 |
| 1 | 8.2pF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C6 |
| 24 | 100nF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C7, C8, C9, C23, C24, C31, C32, C33 +16 |
| 12 | 1uF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C12, C13, C14, C15, C17, C18, C25, C26 +4 |
| 1 | 100uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C16 |
| 1 | 2.2nF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C34 |
| 2 | 22pF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C36, C37 |
| 2 | 2.2uF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C38, C39 |
| 1 | 1nF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C43 |
| 4 | 4.7uF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C50, C51, C52, C53 |
| 1 | 47uF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C61 |
| 1 | 22uF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C62 |
| 1 | 4.7uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C63 |
| 5 | 1k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3, R6, R42, R45, R89 |
| 24 | 25Ohm | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4, R5, R7, R8, R17, R18, R19, R20 +16 |
| 12 | R_DIV2 | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R9, R11, R21, R23, R33, R35, R48, R50 +4 |
| 12 | R_DIV1 | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R10, R12, R22, R24, R34, R36, R49, R51 +4 |
| 12 | R_DIV3 | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R13, R14, R25, R26, R37, R38, R54, R55 +4 |
| 1 | 15.4k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R15 |
| 1 | 274k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R16 |
| 1 | 60.4k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R27 |
| 1 | 11.5k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R28 |
| 2 | 75R | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R39, R91 |
| 5 | 10k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R76, R77, R78, R79, R83 |
| 2 | 100R | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R80, R93 |
| 2 | 4k7 | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R81, R82 |
| 1 | Ri_Vol | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R84 |
| 1 | Ri_Cur | R_2512_6332Metric | R85 |
| 1 | Rf_Vol | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R86 |
| 1 | 2k2 | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R87 |
| 1 | Rd_Cur | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R88 |
Qnot design files
The KiCad project lives in the SushEdge/Qnot repository on GitHub; these links point at the commit this page was built from.
- LayoutSush02.kicad_pcb
Qnot: common questions
What microcontroller does the Qnot use?
The Qnot is built around the STM32F405RGTx, from the STM32 family.
How big is the Qnot PCB?
The Qnot measures 34 × 34 mm, has 8 copper layers and is 1.6 mm thick.
How many components are on the Qnot?
211 components, from 65 distinct parts. The full bill of materials is listed on this page.
Where can I download the Qnot design files?
From the SushEdge/Qnot repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Qnot design in my own project?
The repository has no license, so all rights stay with SushEdge. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Qnot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k