PCB-PD

Taran-the-Idiot·Flippy·PCB-PD/PCB-PD.kicad_pcb

PCB-PD layout, top view — open source RP2040/RP2350 board by Taran-the-Idiot

About the PCB-PD

PCB-PD is an open source RP2040/RP2350 PCB design by Taran-the-Idiot, published on GitHub under the MIT license. It is a 2-layer board measuring 105 × 103.7 mm, with 69 components from 38 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the SCT2650STE, MCP1700, USBLC6-2SC6, W25Q16JVSS and MCP23017. By type, the board carries 31 capacitors, 17 resistors, 8 connectors, 7 ICs, 3 switches and 2 diodes.

Main components on the PCB-PD

PCB-PD bill of materials (BOM)

69 components, 38 distinct parts.

QtyPartRefs
1
SCT2650STE
U1
1
RP2040
U2
1
MCP1700
U3
1
USBLC6-2SC6
U4
1
W25Q16JVSS
U5
2
MCP23017
U6, U7
1
12mHz
Y1
1
Conn_Receptacle_3P_Protected
J1
1
USB_C_Receptacle_USB2.0_14P
J2
1
+12V
J6
1
+3V3
J7
1
GND
J8
2
Conn_01x20_Pin
J9, J10
1
Conn_01x12_Pin
J11
3
SW_Push
SW1, SW2, SW3
1
KBPC5010T
D1
1
C48192
D3
1
4.7nf
C3
1
47pf
C4
4
4.7uf
C5, C6, C7, C8
Show 18 more
QtyPartRefs
14
100nf
C9, C10, C18, C20, C21, C23, C24, C25 +6
5
47uf
C11, C12, C13, C14, C15
2
10uf
C16, C17
2
1uf
C19, C22
2
15pf
C29, C30
1
309k
R1
1
76.8k
R2
1
200k
R3
1
20k
R4
1
31.8k
R5
1
10.2k
R6
2
5.1k
R7, R8
2
27
R9, R10
1
1k
R11
2
10k
R12, R16
1
10k
R13
1
300
R14
2
300
R15, R17

PCB-PD design files

The KiCad project lives in the Taran-the-Idiot/Flippy repository on GitHub; these links point at the commit this page was built from.

PCB-PD: common questions

What microcontroller does the PCB-PD use?

The PCB-PD is built around the RP2040, from the RP2040/RP2350 family.

How big is the PCB-PD?

The PCB-PD measures 105 × 103.7 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the PCB-PD?

69 components, from 38 distinct parts. The full bill of materials is listed on this page.

Where can I download the PCB-PD design files?

From the Taran-the-Idiot/Flippy repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the PCB-PD design in my own project?

Yes, under the terms of its MIT license, which Taran-the-Idiot chose for the repository.

Can I test firmware for the PCB-PD without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in Flippy

Similar boards