CACKLE-PSU-2s 40A PSU and charger

techy-robot·CACKLE-PSU-2s_40A_PSU_and_charger

CACKLE-PSU-2s 40A PSU and charger PCB layout, top view — open source WCH CH32/CH55x board by techy-robot

About the CACKLE-PSU-2s 40A PSU and charger PCB

CACKLE-PSU-2s 40A PSU and charger is an open source WCH CH32/CH55x PCB design by techy-robot, published on GitHub under the CC-BY-NC-4.0 license. It is a 4-layer board measuring 45 × 20 mm, with 95 components from 46 distinct parts.

Its main chip is the CH32X035G8U6, from the WCH CH32/CH55x family. Other key parts include the BQ76905RGRR, AP63203WU, BQ24780SRUYR, THVD1420DRLR and TPS7A2633DRV. By type, the board carries 33 resistors, 31 capacitors, 11 connectors, 6 ICs, 6 transistors and 5 diodes.

It belongs with the power & battery and sensors designs in this gallery.

From the project

This is a rather complex power supply unit. It supports USB-C Power Delivery at 9volt 2 amps, and can charge a 2 cell lipo battery. It can pump out 40 amps if the battery supports the current. It also had battery protection and balancing built in, and a RS485 communication unit t

This is a rather complex power supply unit. It supports USB-C Power Delivery at 9volt 2 amps, and can charge a 2 cell lipo battery. It can pump out 40 amps if the battery supports the current. It also had battery protection and balancing built in, and a RS485 communication unit that can translate USB or SPI data to RS485.

The outer copper is 2oz, and the inner is 0.5 oz. Additional metal is needed to support the full current.

Main components on the CACKLE-PSU-2s 40A PSU and charger

CACKLE-PSU-2s 40A PSU and charger bill of materials (BOM)

95 components, 46 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
BQ76905RGRR
U1
1
AP63203WU
U2
1
BQ24780SRUYR
U3
1
THVD1420DRLR
U5
1
CH32X035G8U6
U6
1
TPS7A2633DRV
U7
4
PJA3430, or HL 2320A
Q1, Q2, Q4, Q5
2
Vishay sir404dp, or SiR500DP
Q3, Q6
4
Keystone 6100
J1, J3, J6, J7
1
JST XH-S Balance Plug
J2
4
Keystone 6102
J4, J5, J8, J9
1
G-SWITCH-GT-USB-7025
G-Switch-GT-USB-7025
J10
1
Precidip 853-87-004-20-001101
J13
1
Mitsumi R-667996
SW1
3
GSDH3005
D1, D2, D3
1
2.6~3.1 Fv Green 5ma
D4
1
CDDFN10-3324P
D11
1
6.8uH HPC HPC5040NF-6R8M
L2
1
3.3uH
L3
2
2.2uf, 16v
C2, C24
Show 26 more
QtyPartRefs
10
100nF, 16v
C3, C4, C9, C10, C11, C21, C22, C23 +2
1
1nF, 16v
C5
2
47nF, 16v
C6, C17
4
10uF, 16v
C7, C12, C14, C20
3
220nF, 16v
C13, C18, C19
1
1uf, 16v
C15
1
4.7uF, 16v
C26
2
22uf, 16v CL31A226MOCLNN
C27, C28
2
100PF
100pF
C29, C30
1
10uF, 16v
C31
1
2.2uF, 16v
C33
1
100nF, 16v
C40
1
10mOhm, 1W
R1
1
2OHM
2ohm
R2
3
100OHM
100ohm
R3, R4, R5
3
5.1K
5.1k
R6, R19, R33
3
4.02K
4.02k
R7, R8, R10
1
10OHM
10ohm
R9
5
10K
10k
R11, R20, R23, R24, R29
6
10OHM
10ohm
R12, R15, R16, R17, R21, R22
2
10k
R13, R32
1
1mOhm, 6W
R14
1
5mOhm, 10W, 2818
R18
1
80.6 ohm
R25
3
120 ohm
R26, R27, R28
2
866K
866k
R30, R31

CACKLE-PSU-2s 40A PSU and charger design files

The KiCad project lives in the techy-robot/CACKLE-PSU-2s_40A_PSU_and_charger repository on GitHub; these links point at the commit this page was built from.

CACKLE-PSU-2s 40A PSU and charger: common questions

What microcontroller does the CACKLE-PSU-2s 40A PSU and charger use?

The CACKLE-PSU-2s 40A PSU and charger is built around the CH32X035G8U6, from the WCH CH32/CH55x family.

How big is the CACKLE-PSU-2s 40A PSU and charger PCB?

The CACKLE-PSU-2s 40A PSU and charger measures 45 × 20 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the CACKLE-PSU-2s 40A PSU and charger?

95 components, from 46 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the CACKLE-PSU-2s 40A PSU and charger design files?

From the techy-robot/CACKLE-PSU-2s_40A_PSU_and_charger repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the CACKLE-PSU-2s 40A PSU and charger design in my own project?

It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.

Can I test firmware for the CACKLE-PSU-2s 40A PSU and charger without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug WCH CH32/CH55x firmware against it before you order a PCB.

Similar boards