CACKLE-PSU-USB 2A PSU 1side

techy-robot·CACKLE-PSU-USB_2A_PSU_1side

CACKLE-PSU-USB 2A PSU 1side PCB layout, top view — open source WCH CH32/CH55x board by techy-robot

About the CACKLE-PSU-USB 2A PSU 1side PCB

CACKLE-PSU-USB 2A PSU 1side is an open source WCH CH32/CH55x PCB design by techy-robot, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 30 × 20 mm, with 42 components from 27 distinct parts.

Its main chip is the CH32X035G8U6, from the WCH CH32/CH55x family. Other key parts include the FAN3111E, AP63203WU, INA219AxDCN, THVD1420DRLR and TPS7A2633DRV. By type, the board carries 13 capacitors, 11 resistors, 6 ICs, 6 connectors, 3 diodes and 2 transistors.

It belongs with the sensors designs in this gallery.

From the project

The main ICs are an mcu, and a 5v 2a switching regulator. The system can theoretically handle 20 volt spikes, but this is mostly meant for 5v output on one side only.

The main ICs are an mcu, and a 5v 2a switching regulator. The system can theoretically handle 20 volt spikes, but this is mostly meant for 5v output on one side only.

The MCU has several purposes: - Manage USB-C PD negotiations over the CC pins (built in PHY) - Report voltage & current sensor data over the bus - Act as a host adapter to convert USB or SPI data to rs485 bus commands and back. Helpful for debugging the system via a laptop, or if your main compute board needs to control the motors and sensors and doesn't have RS485 built in.

Main components on the CACKLE-PSU-USB 2A PSU 1side

CACKLE-PSU-USB 2A PSU 1side bill of materials (BOM)

42 components, 27 distinct parts.

QtyPartRefs
1
FAN3111E
U1
1
AP63203WU
U2
1
INA219AxDCN
U3
1
CH32X035G8U6
U4
1
THVD1420DRLR
U5
1
TPS7A2633DRV
U7
2
PJA3430, or HL 2320A
Q1, Q2
1
Precidip 853-87-004-20-001101
J1
2
Keystone 3579
J3, J7
2
Keystone 3569
J5, J9
1
G-Switch-GT-USB-7025
J10
1
GSDH3005
D3
1
2.6~3.1 Fv Green 5ma
D4
1
CDDFN10-3324P
D11
1
2.2uH, WIP322512A-2R2MLDG
L3
3
10uF, 16v
C1, C7, C31
4
22uf, 16v CL31A226MOCLNN
C2, C3, C27, C28
4
100nF, 16v
C4, C5, C32, C40
1
4.7uF, 16v
C6
1
2.2uF, 16v
C33
Show 7 more
QtyPartRefs
1
50mOhm
R1
1
2ohm
R2
2
10k
R3, R4
1
10ohm
R9
2
5.1k
R19, R33
1
80.6 ohm
R25
3
120 ohm
R26, R27, R28

CACKLE-PSU-USB 2A PSU 1side design files

The KiCad project lives in the techy-robot/CACKLE-PSU-USB_2A_PSU_1side repository on GitHub; these links point at the commit this page was built from.

CACKLE-PSU-USB 2A PSU 1side: common questions

What microcontroller does the CACKLE-PSU-USB 2A PSU 1side use?

The CACKLE-PSU-USB 2A PSU 1side is built around the CH32X035G8U6, from the WCH CH32/CH55x family.

How big is the CACKLE-PSU-USB 2A PSU 1side PCB?

The CACKLE-PSU-USB 2A PSU 1side measures 30 × 20 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the CACKLE-PSU-USB 2A PSU 1side?

42 components, from 27 distinct parts. The full bill of materials is listed on this page.

Where can I download the CACKLE-PSU-USB 2A PSU 1side design files?

From the techy-robot/CACKLE-PSU-USB_2A_PSU_1side repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the CACKLE-PSU-USB 2A PSU 1side design in my own project?

It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.

Can I test firmware for the CACKLE-PSU-USB 2A PSU 1side without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug WCH CH32/CH55x firmware against it before you order a PCB.

Similar boards