ESP32-Data-Acquisition-Board

TheBigBoschi·ESP32-Data-Acquisition-Board-PCB·Kicad Project/ESP32 Data Acquisition Board.kicad_pcb

ESP32-Data-Acquisition-Board layout, top view — open source ESP32 board by TheBigBoschi

About the ESP32-Data-Acquisition-Board

ESP32-Data-Acquisition-Board is an open source ESP32 PCB design by TheBigBoschi, published on GitHub. It is a 2-layer board measuring 99.1 × 99.1 mm, with 83 components from 30 distinct parts.

Its main chip is the ESP32-WROOM-32D, from the ESP32 family. Other key parts include the TPS63020, TF-CARD-9P, HX25Q16DRG, BMP280 and E22-900M22S. By type, the board carries 24 resistors, 23 capacitors, 11 test points, 9 connectors, 8 ICs and 4 transistors.

It belongs with the power & battery, sensors and rf & radio designs in this gallery.

From the project

Custom PCB holding an ESP32, various sensor, a LoRa transmitter and the power management to run off a single lithium battery, cherged by solar power.

To keep the development time short for this first revision I have made extensive use of various commercial modules, such as a TP4056 module, a few TPS63020 and a CN3791 to handle the power conversion. In the second revision they will be integrated directly on the board.

Particular care has been taken to properly decouple the ESP32 power supply, as a switching regulators are slow to react to the sudden bursts of energy required by the ESP32 transmitting data, and various capacitor have been added to give time to the regulator to respond.

Main components on the ESP32-Data-Acquisition-Board

ESP32-Data-Acquisition-Board bill of materials (BOM)

83 components, 30 distinct parts.

QtyPartRefs
2
TPS63020
U1, U2
1
~
U3
1
TF-CARD-9P
Micro SD
BXCONN(宝讯)
U4
1
HX25Q16DRG
HGC(深圳汉芯)
U5
1
BMP280
U6
1
E22-900M22S
EBYTE(亿佰特)
U7
1
ESP32-WROOM-32D
U8
3
SI2301CDS-T1-GE3
SI2301
VISHAY(威世)
Q1, Q3, Q4
1
Si2302CDS-T1-GE3
Si2302
VISHAY(威世)
Q2
1
KF141R-2.54-5P
SHT40 Connector
KEFA(科发)
CN1
1
KF141R-2.54-5P
SPS30 Connector
KEFA(科发)
CN2
1
VBATT
J1
1
VSOLAR
J2
1
CN3791
J3
2
Spare
J4, J5
1
2.54-2*5P简牛
HDR-IDC-2.54-2X5P
BOOMELE(博穆精密)
J6
1
BH254V-6P
XFCN(兴飞)
J7
1
TS110926045
~
HanElectricity(瀚源)
SW_RST1
11
TestPoint
TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 +3
1
LED
D1
Show 10 more
QtyPartRefs
2
M7F
D2, D3
10
100nF
C1, C2, C4, C6, C7, C9, C12, C17 +2
8
10uF
C3, C5, C8, C11, C14, C16, C19, C21
2
47uF
C10, C13
2
22uF
C15, C18
1
1uF
C23
5
5K
R1, R13, R14, R16, R17
11
10k
R2, R3, R4, R5, R6, R9, R10, R11 +3
2
100k
R7, R8
6
100R
R18, R19, R20, R21, R22, R23

ESP32-Data-Acquisition-Board design files

The KiCad project lives in the TheBigBoschi/ESP32-Data-Acquisition-Board-PCB repository on GitHub; these links point at the commit this page was built from.

ESP32-Data-Acquisition-Board: common questions

What microcontroller does the ESP32-Data-Acquisition-Board use?

The ESP32-Data-Acquisition-Board is built around the ESP32-WROOM-32D, from the ESP32 family.

How big is the ESP32-Data-Acquisition-Board?

The ESP32-Data-Acquisition-Board measures 99.1 × 99.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the ESP32-Data-Acquisition-Board?

83 components, from 30 distinct parts. The full bill of materials is listed on this page.

Where can I download the ESP32-Data-Acquisition-Board design files?

From the TheBigBoschi/ESP32-Data-Acquisition-Board-PCB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the ESP32-Data-Acquisition-Board design in my own project?

The repository has no license, so all rights stay with TheBigBoschi. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the ESP32-Data-Acquisition-Board without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards