HeaterControl
TheTosters·HeaterControl·hardware/universalSensor/HeaterControl.kicad_pcb
About the HeaterControl PCB
HeaterControl is an open source PCB design by TheTosters, published on GitHub under the BSD-3-Clause license. It is a 2-layer board measuring 32.8 × 24.9 mm, with 16 components from 13 distinct parts.
Other key parts include the BL654 and SHT30-DIS-B. By type, the board carries 6 resistors, 3 connectors, 2 ICs, 2 capacitors, 1 switch and 1 diode.
It belongs with the sensors designs in this gallery.
From the project
Multi node heater control on Nordic BTLE
You also need nrfprog tools and small patch for SDK from CMSIS. But this is handled by
This is super-glue solution, so your eyes will bleeed... It will use host compiler (not cross-compiler) to build host based tests. It is NOT ment to test all, only most complicated logic. So to have test build and run you have to:
Main components on the HeaterControl
HeaterControl bill of materials (BOM)
16 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BL654 | BL654 | U2 |
| 1 | SHT30-DIS-B | DFN250X250X100-9N | U3 |
| 1 | DS18B20 | PinHeader_1x03_P2.54mm_Vertical_SMD_Pin1Left | J1 |
| 1 | DEV_PORT | PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | Ext | PinHeader_2x04_P1.00mm_Vertical_SMD | J4 |
| 1 | Battery | Cr2032-Holder | B1 |
| 1 | BTN | R_1206_3216Metric | SW1 |
| 1 | OSTB0603C1C-A | LED_PACKAGE_1.6x1.5mm | D1 |
| 1 | 100nF | C_0402_1005Metric | C1 |
| 1 | 10uF | CP_EIA-2012-12_Kemet-R | C2 |
| 3 | 4,7k | R_0402_1005Metric | R1, R2, R4 |
| 1 | 22 | R_0402_1005Metric | R3 |
| 2 | 10 | R_0402_1005Metric | R5, R6 |
HeaterControl design files
The KiCad project lives in the TheTosters/HeaterControl repository on GitHub; these links point at the commit this page was built from.
HeaterControl: common questions
How big is the HeaterControl PCB?
The HeaterControl measures 32.8 × 24.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the HeaterControl?
16 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the HeaterControl design files?
From the TheTosters/HeaterControl repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the HeaterControl design in my own project?
Yes, under the terms of its BSD-3-Clause license, which TheTosters chose for the repository.
More boards in HeaterControl
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kPots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956