Universal v3
TheTosters·HeaterControl·hardware/universal_v3/Universal_v3.kicad_pcb
About the Universal v3 PCB
Universal v3 is an open source PCB design by TheTosters, published on GitHub under the BSD-3-Clause license. It is a 2-layer board measuring 35.3 × 30.2 mm, with 16 components from 13 distinct parts.
Other key parts include the MS88SF2, BME680 and SHT30-DIS-B. By type, the board carries 4 connectors, 4 resistors, 3 ICs, 3 capacitors and 1 diode.
It belongs with the sensors designs in this gallery, and the repository also holds 1 earlier revision of it.
From the project
Multi node heater control on Nordic BTLE
You also need nrfprog tools and small patch for SDK from CMSIS. But this is handled by
This is super-glue solution, so your eyes will bleeed... It will use host compiler (not cross-compiler) to build host based tests. It is NOT ment to test all, only most complicated logic. So to have test build and run you have to:
Main components on the Universal v3
Universal v3 bill of materials (BOM)
16 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MS88SF2 | MS88SF2 | U1 |
| 1 | BME680 | Bosch_LGA-8_3x3mm_P0.8mm_ClockwisePinNumbering | U2 |
| 1 | SHT30-DIS-B | DFN250X250X100-9N | U3 |
| 1 | DS18B20 | 3Pads | J1 |
| 1 | PROG_PORT | 5xPad | J2 |
| 1 | EXT_PORT | 5xPad | J3 |
| 1 | BTN | PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | Battery | Cr2032-Holder | B1 |
| 1 | LED_BARG | Everlight_19-237_R6GHBHC-M07_2T | D1 |
| 2 | 100nF | C_0402_1005Metric | C1, C3 |
| 1 | 10uF | CP_EIA-2012-12_Kemet-R | C2 |
| 3 | 10 | R_0402_1005Metric | R1, R2, R3 |
| 1 | 4,7k | R_0402_1005Metric | R4 |
Universal v3 design files
The KiCad project lives in the TheTosters/HeaterControl repository on GitHub; these links point at the commit this page was built from.
Universal v3: common questions
How big is the Universal v3 PCB?
The Universal v3 measures 35.3 × 30.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Universal v3?
16 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Universal v3 design files?
From the TheTosters/HeaterControl repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Universal v3 design in my own project?
Yes, under the terms of its BSD-3-Clause license, which TheTosters chose for the repository.
More boards in HeaterControl
Earlier revisions in the repo: Universal_v2
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kPots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956