Laas stepper

thomasfla·ARDUINO_PICO_TMC2130·hardware/laas_stepper/laas_stepper.kicad_pcb

Laas stepper PCB layout, top view — open source RP2040/RP2350 board by thomasfla

About the Laas stepper PCB

Laas stepper is an open source RP2040/RP2350 PCB design by thomasfla, published on GitHub under the BSD-3-Clause license. It is a 2-layer board measuring 100 × 60 mm, with 26 components from 16 distinct parts.

Its main chip is the Pico, from the RP2040/RP2350 family. Other key parts include the TSR1-2433E and SilentStepStick-TMC2130. By type, the board carries 7 connectors, 5 capacitors, 4 modules, 4 resistors, 3 ICs and 1 transistor.

It belongs with the robotics & motion designs in this gallery.

From the project

Control 3 TMC2130 stepper driver via USB comands (TMX2130 + RP2350 / RP2040)

This is configured to control stepper motors of a bambulab A1 mini.

3x SilentStepStick - TMC2130 Stepper Motor Driver 1x Raspberry pi Pico2 dev board

The board will be seen as a virtual COM port.

Send target position, max velocity and max acceleration for all axis (in step, step/s, step/s2)

X 2000 1000 2000\n Y 500 1000 2000\n etc..

The driver will send at a chosen period the motor position and velocity: X 9030 0 Y 4340 0 Z 0 0

Main components on the Laas stepper

Laas stepper bill of materials (BOM)

26 components, 16 distinct parts.

QtyPartRefs
1
Pico
U1
1
TSR1-2433E
U2
1
~
U3
4
SilentStepStick-TMC2130
A1, A2, A3, A4
1
DMG2301L
Q1
4
Conn_01x04_Pin
J1, J2, J3, J5
1
Conn_01x02_Pin
J4
1
Conn_01x02
J7
1
Conn_01x04
J8
1
100k
RV1
1
MSS1P4-M3
D9
3
C
C1, C3, C7
1
22u 50V
C2
1
C_Polarized
C8
3
10k
R1, R2, R3
1
200k
R4

Laas stepper design files

The KiCad project lives in the thomasfla/ARDUINO_PICO_TMC2130 repository on GitHub; these links point at the commit this page was built from.

Laas stepper: common questions

What microcontroller does the Laas stepper use?

The Laas stepper is built around the Pico, from the RP2040/RP2350 family.

How big is the Laas stepper PCB?

The Laas stepper measures 100 × 60 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Laas stepper?

26 components, from 16 distinct parts. The full bill of materials is listed on this page.

Where can I download the Laas stepper design files?

From the thomasfla/ARDUINO_PICO_TMC2130 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Laas stepper design in my own project?

Yes, under the terms of its BSD-3-Clause license, which thomasfla chose for the repository.

Can I test firmware for the Laas stepper without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in ARDUINO_PICO_TMC2130

Similar boards