Analog matrix lc1

tim4431·analog_programmable_matrix·variants/lc1/hardware/analog_matrix_lc1.kicad_pcb

Analog matrix lc1 PCB layout, top view — open source RP2040/RP2350 board by tim4431

About the Analog matrix lc1 PCB

Analog matrix lc1 is an open source RP2040/RP2350 PCB design by tim4431, published on GitHub. It is a 4-layer board measuring 160 × 170 mm, with 387 components from 41 distinct parts.

Its main chip is the Raspberry Pi Pico, from the RP2040/RP2350 family. Other key parts include the ADA4899-1YRDZ, THS3091DDAR, ADR4525BRZ, SN74HC595D and L7805CV. By type, the board carries 162 capacitors, 152 resistors, 62 ICs, 9 connectors and 2 diodes.

From the project

DC-coupled 4x4 programmable analog matrix: signed gains, 1 MHz target, BNC I/O, Pico control, KiCad PCB and enclosure CAD.

LC1 is a separate four-input, four-output programmable analog matrix. It keeps the DC–1 MHz, ±1 V input and ±4 V output into 50 Ω targets of Revision D, using less expensive multiplying DACs and more dual/quad packages. Revision D remains available unchanged.

This is an unbuilt prototype, not a measured 1% instrument. The nominal circuit simulations meet the amplitude-flatness target, but the cheaper DAC's bandwidth is a typical specification. Actual boards need qualification. Use the LC1 PCB, BOM and firmware together; the parts are not drop-in replacements on Revision D.

Analog matrix lc1, from the project README
From the project README

Main components on the Analog matrix lc1

Analog matrix lc1 bill of materials (BOM)

387 components, 41 distinct parts — part numbers from the project's BOM.

QtyPartRefs
16
ADA4899-1YRDZ
U60, U61, U62, U63, U64, U65, U66, U67 +8
4
THS3091DDAR
U90, U91, U92, U93
1
ADR4525BRZ
U110
1
Raspberry Pi Pico
U120
2
SN74HC595D
U121, U122
1
L7805CV
U130
1
L7905CV
U131
8
OPA2810IDR
U200, U201, U202, U203, U204, U205, U206, U207
10
TMUX6136PWR
U220, U221, U222, U223, U224, U225, U226, U227 +2
16
DAC7811IDGSR
U300, U301, U302, U303, U304, U305, U306, U307 +8
1
MCP4728T-E_UN
U400
1
OPA4197IPWR
U401
8
BNC 031-5329-52RFX
J1, J2, J3, J4, J5, J6, J7, J8
1
3-pin terminal
J9
2
1N4002
D1, D2
105
100 nF
C1, C2, C3, C4, C11, C12, C17, C18 +97
16
10 uF
C7, C8, C15, C16, C23, C24, C31, C32 +8
6
1 uF
C34, C68, C102, C136, C188, C190
16
1.0 pF C0G
C41, C46, C51, C56, C75, C80, C85, C90 +8
8
6.8 uF / 25 V
C65, C66, C99, C100, C133, C134, C167, C168
Show 21 more
QtyPartRefs
2
47 uF / 35 V
C193, C197
1
330 nF
C194
2
10 uF / 16 V
C195, C199
1
2.2 uF
C198
4
10 nF
C320, C321, C322, C323
1
1 uF
C327
9
33 ohm
R1, R10, R19, R28, R133, R134, R135, R136 +1
4
1 M
R2, R11, R20, R29
8
49.9 ohm
R3, R12, R21, R30, R56, R80, R104, R128
8
499 ohm
R4, R5, R13, R14, R22, R23, R31, R32
32
1.00 k
R6, R7, R8, R9, R15, R16, R17, R18 +24
32
150R 0.1%
R37, R38, R41, R42, R45, R46, R49, R50 +24
20
100 k
R39, R43, R47, R51, R57, R63, R67, R71 +12
4
549 ohm
R53, R77, R101, R125
12
10.0 k
R54, R78, R102, R126, R300, R301, R302, R303 +4
4
20.0 k
R55, R79, R103, R127
4
1.21 k
R58, R82, R106, R130
4
402 ohm
R59, R83, R107, R131
4
49.9 ohm
R60, R84, R108, R132
5
10 k
R138, R139, R140, R141, R146
2
4.70 k
R308, R309

Analog matrix lc1 design files

The KiCad project lives in the tim4431/analog_programmable_matrix repository on GitHub; these links point at the commit this page was built from.

Analog matrix lc1: common questions

What microcontroller does the Analog matrix lc1 use?

The Analog matrix lc1 is built around the Raspberry Pi Pico, from the RP2040/RP2350 family.

How big is the Analog matrix lc1 PCB?

The Analog matrix lc1 measures 160 × 170 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Analog matrix lc1?

387 components, from 41 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Analog matrix lc1 design files?

From the tim4431/analog_programmable_matrix repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Analog matrix lc1 design in my own project?

The repository has no license, so all rights stay with tim4431. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Analog matrix lc1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in analog_programmable_matrix

Similar boards