Liquid simulator
TomasD-git·Liquid-simulator·liquid simulator/liquid simulator.kicad_pcb
About the Liquid simulator PCB
Liquid simulator is an open source ESP32 PCB design by TomasD-git, published on GitHub. It is a 2-layer board measuring 38 × 45.5 mm, with 30 components from 16 distinct parts.
Its main chip is the ESP32-C6-MINI-1/U, from the ESP32 family. Other key parts include the GT-USB-7010ASV, AP2112K-3.3 and BMI270. By type, the board carries 14 capacitors, 9 resistors, 4 ICs, 2 switches and 1 connector.
It belongs with the sensors designs in this gallery.
From the project
Basically simulates liquid using imu and esp32 C6
Main components on the Liquid simulator
Liquid simulator bill of materials (BOM)
30 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | GT-USB-7010ASV G-Switch(品赞) | USB-C-SMD_G-SWITCH_GT-USB-7010ASV | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | BMI270 | XDCR_BMI270 | U4 |
| 1 | ESP32-C6-MINI-1/U | ESP32-C6-MINI-1 | U5 |
| 1 | Display 1.28 Inch | PinHeader_1x07_P2.54mm_Vertical | J2 |
| 2 | SW_Push | SW_Push_1P1T_XKB_TS-1187A | SW1, SW2 |
| 3 | 10UF 10uF | C_0603_1608Metric | C1, C3, C5 |
| 2 | 1UF 1uF | C_0603_1608Metric | C2, C4 |
| 1 | 47UF 47uF | C_0805_2012Metric | C6 |
| 6 | 100NF 100nF | C_0402_1005Metric | C7, C8, C9, C13, C24, C25 |
| 2 | 1UF 1uF | C_0402_1005Metric | C10, C23 |
| 2 | 22 | R_0402_1005Metric | R1, R2 |
| 2 | 2.2K | R_0402_1005Metric | R3, R4 |
| 2 | 10K | R_0402_1005Metric | R5, R8 |
| 1 | 330 | R_0402_1005Metric | R6 |
| 2 | 5.1K | R_0402_1005Metric | R7, R10 |
Liquid simulator design files
The KiCad project lives in the TomasD-git/Liquid-simulator repository on GitHub; these links point at the commit this page was built from.
Liquid simulator: common questions
What microcontroller does the Liquid simulator use?
The Liquid simulator is built around the ESP32-C6-MINI-1/U, from the ESP32 family.
How big is the Liquid simulator PCB?
The Liquid simulator measures 38 × 45.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Liquid simulator?
30 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Liquid simulator design files?
From the TomasD-git/Liquid-simulator repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Liquid simulator design in my own project?
The repository has no license, so all rights stay with TomasD-git. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Liquid simulator without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k