28 open source boards using the GT-USB-7010ASV
Real designs built with the GT-USB-7010ASV, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
CloudSmoker
cwgstreet
70 × 70 mm56 parts4LMIT24FABulous board
FPGA-Research
101.2 × 63.5 mm75 parts4LApache-2.06STM32
Ollyfc
rland93
45 × 98 mm101 parts4LMPL-2.02RP2040/RP2350
Billig
playlogo
86 × 74 mm58 parts2LTAPR-OHL-1.02GD32
KiCad-GD32FxxxRx no-PHY
vanvught
77.2 × 59.7 mm48 parts2LMIT2RP2040/RP2350
Devboardrp2350
espcaa
59.2 × 26.4 mm43 parts4LNo license2KiCad-GD32F207RG-Pixel-8
vanvught
65.5 × 55 mm29 parts2LMIT2STM32
Main
Team-Micras
50 × 90 mm138 parts4LNo license1GD32
Kicad-GD32F470VG-Pixel-16
vanvught
96 × 110.1 mm95 parts2LMIT1GD32
KiCad-GD32F427RE-LTC-SMPTE-no-PHY
vanvught
66.6 × 69.3 mm52 parts2LMIT1ESP32
Cc1101 receiver esp32
maxim75
49 × 55 mm39 parts4LNo license1KiCad-DMX-Pixel-1
vanvught
84.8 × 62.1 mm31 parts2LMIT1STM32
STM32F4Example
JAS-UCF
27 × 44.7 mm24 parts2LGPL-3.01Artificer-A1-Single-Board-Computer
MattSpot10
115 × 90 mm486 parts6LMIT0RP2040/RP2350
Adventure board
picorubykaigi
90 × 130 mm361 parts4LCERN-OHL-P-2.00ESP32
LowJungle
playlogo
371.5 × 133.4 mm300 parts2LTAPR-OHL-1.00ESP32
Nivara
WenerrP
120 × 79.5 mm172 parts4LNo license0ESP32
Waypoint
M-Mrk
140 × 80 mm129 parts4LNo license0Skibidi usb hub
tobycm
50 × 65 mm83 parts4LMIT0RP2040/RP2350
E-Ink-Badge
Acidicts
77.5 × 48.5 mm78 parts2LNo license0ESP32
Bike-Mini speedo
InfinityTech100
54 × 35 mm67 parts4LNo license0Nordic nRF
Slim-Sleep-Tracker
NicholasKorth
31.8 × 15.3 mm57 parts4LCC-BY-NC-4.00STM32
Battery-Remoter
chenzhjie
35.2 × 51 mm44 parts2LMIT0ESP32
ESP32-S3-DevBoard
TomasD-git
21.5 × 51.8 mm42 parts4LMIT0ESP32
Liquid simulator
TomasD-git
38 × 45.5 mm30 parts2LNo license0Tagmod hw
goliothlabs
21.1 × 27.3 mm22 parts2LCERN-OHL-P-2.00RP2040/RP2350
Devbackup
espcaa
33.6 × 25.4 mm41 parts2LNo license2PCB USB
WenerrP
33.4 × 18 mm6 parts2LNo license0
How designs wire the GT-USB-7010ASV
Read from the KiCad layouts of 26 open source designs, one per repository: what each pin of the GT-USB-7010ASV connects to, and the resistors, capacitors and other passives placed on it.
- The CC1 pin has a resistor to GND on 25 of 26 designs, most often 5.1 kΩ.
- The CC2 pin has a resistor to GND on 24 of 26 designs, most often 5.1 kΩ.
- The SBU1 pin is left unconnected on 23 of 26 designs (a signal on 2).
- The SBU2 pin is left unconnected on 23 of 26 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SHELLpin 1, 2, 3, 4 | Connected to: GND 88% | — |
| GNDpin A1B12, B1A12 | Connected to: GND 100% | — |
| VBUSpin A4B9, B4A9 | Connected to: 5V 81% |
|
| CC1pin A5 | Connected to: Signal 100% |
|
| DP1pin A6 | Connected to: Signal 85% · not connected 15% |
|
| DN1pin A7 | Connected to: Signal 85% · not connected 15% |
|
| SBU1pin A8 | Connected to: Not connected 88% | — |
| CC2pin B5 | Connected to: Signal 96% |
|
| DP2pin B6 | Connected to: Signal 85% · not connected 15% |
|
| DN2pin B7 | Connected to: Signal 85% · not connected 15% |
|
| SBU2pin B8 | Connected to: Not connected 88% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CloudSmoker by cwgstreet, FABulous board by FPGA-Research, Devbackup by espcaa and Billig by playlogo.
The GT-USB-7010ASV in open source designs
The gallery holds 28 open source boards using the GT-USB-7010ASV from 26 GitHub repositories; a typical one measures about 62.3 × 60.9 mm and carries around 57 components.
50% are two-layer designs, the rest use four layers or more, and 61% carry an open source license.
The most starred is CloudSmoker by cwgstreet.
Parts used alongside the GT-USB-7010ASV
Microcontrollers on boards using the GT-USB-7010ASV
What boards using the GT-USB-7010ASV are built for
GT-USB-7010ASV: common questions
Where can I find a GT-USB-7010ASV reference design?
Each of the 28 boards on this page is a real design using the GT-USB-7010ASV. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the GT-USB-7010ASV CC1 pin?
The CC1 pin has a resistor to GND on 25 of 26 designs, most often 5.1 kΩ. Counted from the KiCad layouts of 26 open source designs using the GT-USB-7010ASV.
What resistor goes on the GT-USB-7010ASV CC2 pin?
The CC2 pin has a resistor to GND on 24 of 26 designs, most often 5.1 kΩ. Counted from the KiCad layouts of 26 open source designs using the GT-USB-7010ASV.
How is the GT-USB-7010ASV SBU1 pin connected?
The SBU1 pin is left unconnected on 23 of 26 designs (a signal on 2). Counted from the KiCad layouts of 26 open source designs using the GT-USB-7010ASV.
What parts are used alongside the GT-USB-7010ASV?
The AMS1117-3.3, W25Q128JVS, 74HCT245, 74LVC2G125 and ABM8-272-T3_C20625731 appear in the most repositories here.
Which microcontrollers do boards using the GT-USB-7010ASV use?
Most are built on ESP32 (8), RP2040/RP2350 (5), STM32 (4) and GD32 (3).
How big is a typical board using the GT-USB-7010ASV?
The median is 62.3 × 60.9 mm, and 50% are two-layer designs.
What is the most popular open source board using the GT-USB-7010ASV?
By GitHub stars, CloudSmoker by cwgstreet, with 24 stars.
Can I simulate one of these boards using the GT-USB-7010ASV before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.