Feeder Testplatine
Tynogc·PickAndPlace_Electronic·Feeder_PCB/Feeder.kicad_pcb
About the Feeder Testplatine PCB
Feeder Testplatine is an open source STM32 PCB design by Tynogc, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 40 × 64 mm, with 48 components from 19 distinct parts.
Its main chip is the STM32F042K6Tx, from the STM32 family. Other key parts include the AP111733, WS2812B and MCP2562-E/SN. By type, the board carries 16 resistors, 11 capacitors, 9 diodes, 7 connectors, 4 ICs and 1 crystal.
From the project
The Electronic-Side of an automatic SMT Pick&Place-System
Leiterplatten und embedded-Software für den Pick&Place Automaten
zur Verwendung dieses Repos sind noch die folgenden Repositorys nötig: https://github.com/Virtex7/PhilippsKicadBauteile https://github.com/ep092/library_toni.pretty
Diese enthalten KiCAD-Bauteile und Schaltplansymbole
Main components on the Feeder Testplatine
Feeder Testplatine bill of materials (BOM)
48 components, 19 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP111733 | SOT-223 | U2 |
| 1 | STM32F042K6Tx | LQFP-32_7x7mm_Pitch0.8mm | U3 |
| 1 | WS2812B | LED_WS2812B-PLCC4 | U4 |
| 1 | MCP2562-E/SN | SOIC-8_3.9x4.9mm_Pitch1.27mm | U5 |
| 1 | 8MHz | CSTCE_3,2x1,3 | Y1 |
| 1 | CONN_01X05 | JST_XH_B05B-XH-A_05x2.50mm_Straight | P1 |
| 2 | CONN_01X08 | Socket_Strip_Straight_1x08_Pitch2.54mm | P2, P4 |
| 1 | CONN_01X01 | Pin_Header_Straight_1x01_Pitch2.54mm | P3 |
| 1 | CONN_02X03 | Pin_Header_Angled_2x03_Pitch2.54mm | P5 |
| 1 | CONN_01X04 | JST_PH_B4B-PH-K_04x2.00mm_Straight | P6 |
| 1 | CONN_01X03 | Pin_Header_Straight_1x03_Pitch2.54mm | P7 |
| 1 | ZENER | D_MiniMELF_Standard | D1 |
| 8 | LED | LED_0603 | D2, D3, D4, D5, D6, D7, D8, D9 |
| 2 | 10µ | C_0805 | C1, C2 |
| 8 | 100n | C_0603 | C3, C4, C5, C6, C7, C9, C10, C11 |
| 1 | 1µ | C_0603 | C8 |
| 7 | 10k | R_0603 | R1, R10, R11, R12, R13, R14, R15 |
| 8 | 470 | R_0603 | R2, R3, R4, R5, R6, R7, R8, R9 |
| 1 | 220 | R_0603 | R16 |
Feeder Testplatine design files
The KiCad project lives in the Tynogc/PickAndPlace_Electronic repository on GitHub; these links point at the commit this page was built from.
Feeder Testplatine: common questions
What microcontroller does the Feeder Testplatine use?
The Feeder Testplatine is built around the STM32F042K6Tx, from the STM32 family.
How big is the Feeder Testplatine PCB?
The Feeder Testplatine measures 40 × 64 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Feeder Testplatine?
48 components, from 19 distinct parts. The full bill of materials is listed on this page.
Where can I download the Feeder Testplatine design files?
From the Tynogc/PickAndPlace_Electronic repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Feeder Testplatine design in my own project?
Yes, under the terms of its GPL-3.0 license, which Tynogc chose for the repository.
Can I test firmware for the Feeder Testplatine without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in PickAndPlace_Electronic
Led
Tynogc
57.5 × 67.5 mm63 parts2LGPL-3.01LED Panel Hex
Tynogc
39 × 55.5 mm52 parts2LGPL-3.01Raspberry Pi
DomController
Tynogc
56 × 90 mm41 parts2LGPL-3.01LED Panel Flat
Tynogc
50 × 50 mm37 parts2LGPL-3.01AVR/Arduino
Gabel
Tynogc
33 × 72 mm35 parts2LGPL-3.01LED Panel Hex schraeg
Tynogc
18 × 55.5 mm33 parts2LGPL-3.01LED Panel Hex gerade
Tynogc
18 × 50.8 mm19 parts2LGPL-3.01
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k