UsbServoController

ucandevices·UsbServoController·PCB/usbservocontroller/usbservocontroller.kicad_pcb

UsbServoController PCB layout, top view — open source RISC-V board by ucandevices

About the UsbServoController PCB

UsbServoController is an open source RISC-V PCB design by ucandevices, published on GitHub under the MIT license. It is a 2-layer board measuring 66 × 38 mm, with 59 components from 26 distinct parts.

Its main chip is the CH32V203C8T6, from the RISC-V family. Other key parts include the HT7533-1, SRV05-4 and INA180A2. By type, the board carries 22 resistors, 18 capacitors, 9 connectors, 4 ICs, 3 diodes and 1 crystal.

It belongs with the robotics & motion and wearables designs in this gallery.

From the project

12-channel USB-C servo controller, Pololu Maestro compatible, MCP server for AI agents. Open hardware, CH32V203 RISC-V

Open-source alternative to the Pololu Mini Maestro 12 that speaks the Maestro serial protocols, so Maestro libraries work unchanged — plus USB-C, servo-rail current and voltage sensing, on-board scripts. Built for JLCPCB turnkey assembly, ≈ $4.43 per board at 100 units against $29.95 for the Maestro.

tools/servomcp.py is an MCP server that lets an AI agent move servos, run poses and sequences, and read rail current/voltage, with guardrails: per-channel limits, ramped moves, overcurrent stop. pip install -r tools/requirements.txt`, then:

UsbServoController, from the project README
From the project README

Main components on the UsbServoController

UsbServoController bill of materials (BOM)

59 components, 26 distinct parts.

QtyPartRefs
1
CH32V203C8T6
U1
1
HT7533-1
U2
1
SRV05-4
U3
1
INA180A2
U4
1
8MHz
Y1
1
USB-C
J1
1
SERVO PWR
J2
1
SIG 0-5
J3
1
SIG 6-11
J4
1
V+ 0-5
J5
1
V+ 6-11
J6
1
GND 0-5
J7
1
GND 6-11
J8
1
SDI (DNP)
J9
1
BOOT0_SEL
BOOT0_SEL
1
VSRV_BRIDGE
JP1
2
B5819W
D1, D2
1
RED
D3
10
100nF
C1, C2, C3, C4, C5, C6, C7, C8 +2
3
10uF
C9, C10, C11
Show 6 more
QtyPartRefs
1
1uF
C12
2
30pF
C13, C14
2
470uF/16V
C15, C16
13
220R
R1, R2, R3, R4, R5, R6, R7, R8 +5
8
5K1
R14, R15, R16, R17, R19, R20, R21, R22
1
5mR
R18

UsbServoController design files

The KiCad project lives in the ucandevices/UsbServoController repository on GitHub; these links point at the commit this page was built from.

UsbServoController: common questions

What microcontroller does the UsbServoController use?

The UsbServoController is built around the CH32V203C8T6, from the RISC-V family.

How big is the UsbServoController PCB?

The UsbServoController measures 66 × 38 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the UsbServoController?

59 components, from 26 distinct parts. The full bill of materials is listed on this page.

Where can I download the UsbServoController design files?

From the ucandevices/UsbServoController repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the UsbServoController design in my own project?

Yes, under the terms of its MIT license, which ucandevices chose for the repository.

Can I test firmware for the UsbServoController without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RISC-V firmware against it before you order a PCB.

Similar boards