HalfLife-Project-Week-1
VickyOnTop2805·HalfLife-Project-Week-1·Starbie-PCB/Starbie-PCB.kicad_pcb
About the HalfLife-Project-Week-1 PCB
HalfLife-Project-Week-1 is an open source ESP32 PCB design by VickyOnTop2805, published on GitHub. It is a 2-layer board measuring 70 × 48.5 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
It belongs with the displays & leds and sensors designs in this gallery.

Main components on the HalfLife-Project-Week-1
HalfLife-Project-Week-1 bill of materials (BOM)
7 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U1 |
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U2 |
| 1 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 2 | SW_Push | SW_PUSH_6mm | SW1, SW2 |
| 1 | 10k | R_0805_2012Metric | R1 |
HalfLife-Project-Week-1 design files
The KiCad project lives in the VickyOnTop2805/HalfLife-Project-Week-1 repository on GitHub; these links point at the commit this page was built from.
HalfLife-Project-Week-1: common questions
What microcontroller does the HalfLife-Project-Week-1 use?
The HalfLife-Project-Week-1 is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the HalfLife-Project-Week-1 PCB?
The HalfLife-Project-Week-1 measures 70 × 48.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the HalfLife-Project-Week-1?
7 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the HalfLife-Project-Week-1 design files?
From the VickyOnTop2805/HalfLife-Project-Week-1 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the HalfLife-Project-Week-1 design in my own project?
The repository has no license, so all rights stay with VickyOnTop2805. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the HalfLife-Project-Week-1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k