Micromouse
wuehr1999·micromouse·kicad/pcb/micromouse/micromouse.kicad_pcb
About the Micromouse PCB
Micromouse is an open source ESP32 PCB design by wuehr1999, published on GitHub under the MIT license. It is a 2-layer board measuring 80 × 80.2 mm, with 83 components from 31 distinct parts.
Its main chip is the ESP32_WROOM_32, from the ESP32 family. Other key parts include the DRV8833, LT1117 and BNO055. By type, the board carries 32 resistors, 22 capacitors, 13 connectors, 5 ICs, 4 switches and 3 diodes.
It belongs with the robotics & motion, sensors and power & battery designs in this gallery.
From the project
Micromouse competition robot
This micromouse (or at least wall follower :)) is constructed for the Istrobot micromouse competition held in Bratislava, Slowenia. As beginners are welcome, the maze will always be solvable by just following the left or right wall, so this should be the first big milestone to achieve.
The mouse is built by the following components, all connected on a custom PCB by Jonas Wühr:

Main components on the Micromouse
Micromouse bill of materials (BOM)
83 components, 31 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32_WROOM_32 | ESP32-WROOM-32 | U1 |
| 1 | DRV8833 | TSSOP-16-1EP_4.4x5mm_Pitch0.65mm | U2 |
| 2 | LT1117 | SOT-223 | U3, U5 |
| 1 | BNO055 | LGA-28-5832 | U4 |
| 1 | BC847 | SOT-23 | Q1 |
| 3 | CONN_01X02 | PinSocket_1x02_P2.54mm_Vertical | P1, P2, P3 |
| 7 | CONN_01X03 | PinHeader_1x03_P2.54mm_Vertical | P4, P5, P6, P7, P8, P9, P10 |
| 2 | CONN_01X14 | PinHeader_1x14_P2.54mm_Vertical | P11, P12 |
| 1 | CONN_01X04 | PinSocket_1x04_P2.54mm_Vertical | P13 |
| 2 | MHP_3.2_5.0 | MHP_3.2_5.0 | MECH1, MECH2 |
| 1 | SPEAKER | PinHeader_1x02_P2.54mm_Vertical | SP1 |
| 1 | switches:Würth_WS-SLTV | WE_450404015514 | SW1 |
| 3 | SW_PUSH | smd_push | SW2, SW3, SW4 |
| 3 | LED_Small | LED_0603 | D1, D2, D3 |
| 5 | dnp | C_0603 | C1, C14, C15, C16, C17 |
| 2 | C_0603 | C_0603 | C2, C3 |
| 1 | 6.8nF | C_0603 | C4 |
| 1 | 120nF | C_0603 | C5 |
| 3 | 100nF | C_0603 | C6, C7, C10 |
| 1 | 2.2uF | C_0603 | C8 |
Show 11 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10nF | C_0603 | C9 |
| 2 | CP_Small | TantalC_SizeX_EIA-7343 | C11, C23 |
| 4 | 22u | C_1206 | C12, C13, C19, C20 |
| 2 | 100n | C_0603 | C21, C22 |
| 3 | 1k | R_0603 | R1, R21, R22 |
| 6 | 10k | R_0603 | R2, R3, R4, R5, R26, R27 |
| 2 | 100R | R_0805 | R6, R7 |
| 9 | 0R0 | R_0603 | R8, R11, R12, R15, R28, R31, R33, R35 +1 |
| 9 | dnp | R_0603 | R9, R10, R13, R14, R16, R17, R18, R19 +1 |
| 2 | R_0603 | R_0603 | R23, R24 |
| 1 | 4k7 | R_0603 | R25 |
Micromouse design files
The KiCad project lives in the wuehr1999/micromouse repository on GitHub; these links point at the commit this page was built from.
Micromouse: common questions
What microcontroller does the Micromouse use?
The Micromouse is built around the ESP32_WROOM_32, from the ESP32 family.
How big is the Micromouse PCB?
The Micromouse measures 80 × 80.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Micromouse?
83 components, from 31 distinct parts. The full bill of materials is listed on this page.
Where can I download the Micromouse design files?
From the wuehr1999/micromouse repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Micromouse design in my own project?
Yes, under the terms of its MIT license, which wuehr1999 chose for the repository.
Can I test firmware for the Micromouse without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k