Starbie
young1dev·Starbie·Hardware/Starbie.kicad_pcb
About the Starbie PCB
Starbie is an open source ESP32 PCB design by young1dev, published on GitHub. It is a 2-layer board measuring 115.9 × 108.3 mm, with 13 components from 12 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 4 connectors, 3 resistors, 2 ICs, 2 switches, 1 transistor and 1 diode.
It belongs with the sensors and displays & leds designs in this gallery.
From the project
Starbie is a tiny motion-controlled digital pet — essentially a desktop Tamagotchi with minimal gameplay buttons. Instead of relying entirely on button presses, you interact with the pet by moving the device.
Starbie is a tiny motion-controlled digital pet — essentially a desktop Tamagotchi with minimal gameplay buttons. Instead of relying entirely on button presses, you interact with the pet by moving the device.
Built around the Seeed XIAO ESP32-C3, Starbie uses an OLED display to bring the pet to life and motion input to respond to interactions. My version adds a vibration motor for physical feedback and a custom PCB designed to integrate the electronics used.

Main components on the Starbie
Starbie bill of materials (BOM)
13 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U1 |
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U2 |
| 1 | AO3400A | SOT-23 | Q1 |
| 1 | Conn_01x04_Pin | Display_128x64_096_I2C | J1 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 1 | Batt | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J3 |
| 1 | Vibrator | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J4 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | SS14 | D_SMA | D2 |
| 1 | 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
| 1 | 100 | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R2 |
| 1 | 100k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R3 |
Starbie design files
The KiCad project lives in the young1dev/Starbie repository on GitHub; these links point at the commit this page was built from.
- LayoutHardware/Starbie.kicad_pcb
- SchematicHardware/Starbie.kicad_sch
Starbie: common questions
What microcontroller does the Starbie use?
The Starbie is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Starbie PCB?
The Starbie measures 115.9 × 108.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Starbie?
13 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Starbie design files?
From the young1dev/Starbie repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Starbie design in my own project?
The repository has no license, so all rights stay with young1dev. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Starbie without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k