TECHIN514 Final
yplee948-hub·TECHIN514_Final·Updated System Architecture and Schematics/Techin514_displaydevice.kicad_sch

About the TECHIN514 Final PCB
TECHIN514 Final is an open source ESP32 PCB design by yplee948-hub, published on GitHub. It is a board, with 8 components from 8 distinct parts.
Its main chip is the XIAO-ESP32C3, from the ESP32 family. Other key parts include the SSD1306 OLED. By type, the board carries 3 ICs, 2 capacitors, 1 module, 1 battery holder and 1 switch.
It belongs with the iot & wireless, displays & leds and power & battery designs in this gallery.
From the project
[Sensing Device (ESP32)] --(BLE GATT Notification)--> [Display Device (ESP32)]
[Sensing Device (ESP32)] --(BLE GATT Notification)--> [Display Device (ESP32)]
Logic Flow: 1. Sense: Load cell detects weight change > 0.5g. 2. Verify: ESP32 filters noise and confirms bottle was replaced. 3. Transmit: BLE packet sent to Display Device. 4. Process: Display Device resets the "Dose Timer." 5. Actuate: Stepper motor moves needle back to "Normal" and LED turns green. 6. Decay:** If timer exceeds 24 hours, motor moves needle to "Delayed."
Main components on the TECHIN514 Final
TECHIN514 Final bill of materials (BOM)
8 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32C3 ULN2003 | U1 | |
| 1 | SSD1306 OLED | LGA-14_3x5mm_P0.8mm_LayoutBorder1x6y | U5 |
| 1 | XIAO-ESP32C3 | ESP32-C3-DevKitM-1 | U6 |
| 1 | 28BYJ-48 | M2 | |
| 1 | LiPo 3.7V | BT2 | |
| 1 | SW_Push | SW2 | |
| 1 | 0.1UF 100uF | C1 | |
| 1 | 10UF 0.1uF | C2 |
TECHIN514 Final design files
The KiCad project lives in the yplee948-hub/TECHIN514_Final repository on GitHub; these links point at the commit this page was built from.
TECHIN514 Final: common questions
What microcontroller does the TECHIN514 Final use?
The TECHIN514 Final is built around the XIAO-ESP32C3, from the ESP32 family.
How many components are on the TECHIN514 Final?
8 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the TECHIN514 Final design files?
From the yplee948-hub/TECHIN514_Final repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the TECHIN514 Final design in my own project?
The repository has no license, so all rights stay with yplee948-hub. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the TECHIN514 Final without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k