Eightbots
YuseiIto·eightbots·board/electronics/8bots.kicad_pcb
About the Eightbots PCB
Eightbots is an open source ESP32 PCB design by YuseiIto, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 99 × 74 mm, with 37 components from 24 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the AZ1084-3.3, GY-521, CH340E and DRV8833 Module. By type, the board carries 10 capacitors, 8 resistors, 5 ICs, 5 connectors, 4 diodes and 3 switches.
Main components on the Eightbots
Eightbots bill of materials (BOM)
37 components, 24 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32 | ESP-32SBoard | U1 |
| 1 | AZ1084-3.3 | TO-252-3_TabPin2 | U2 |
| 1 | GY-521 | GY-521_Part_side_up | U3 |
| 1 | CH340E | DIP-10_W7.62mm_LongPads | U4 |
| 1 | DRV8833 Module | DRV8833_Module | U5 |
| 1 | 9V IN | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1 |
| 1 | USB_B_Micro | MicroUSBBoard | J2 |
| 1 | Motor R | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J3 |
| 1 | Motor L | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
| 1 | Motor BAT | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | RotaryEncoder_Switch | RotaryEncoder_Alps_EC12E-Switch_Vertical_H20mm | SW1 |
| 1 | SW_SPDT | SPDT_With_Mounting_Hole | SW3 |
| 1 | SW_SPDT | SW_Slide_SPDT_Straight_CK_OS102011MS2Q | SW4 |
| 1 | SSD1306 | 128x64OLED | Brd1 |
| 1 | LED_RABG | LED_D5.0mm-4_RGB | D1 |
| 2 | LED | LED_D3.0mm | D2, D3 |
| 1 | D | D_A-405_P10.16mm_Horizontal | D4 |
| 7 | 0.1uF | C_Disc_D5.1mm_W3.2mm_P5.00mm | C1, C2, C3, C6, C7, C8, C9 |
| 1 | 10uF | CP_Radial_D5.0mm_P2.50mm | C4 |
Show 4 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 22uF | CP_Radial_D5.0mm_P2.50mm | C5 |
| 1 | 100uF | CP_Radial_D5.0mm_P2.50mm | C10 |
| 5 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R3, R4, R9, R10, R11 |
| 3 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R6, R7, R8 |
Eightbots design files
The KiCad project lives in the YuseiIto/eightbots repository on GitHub; these links point at the commit this page was built from.
Eightbots: common questions
What microcontroller does the Eightbots use?
The Eightbots is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the Eightbots PCB?
The Eightbots measures 99 × 74 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Eightbots?
37 components, from 24 distinct parts. The full bill of materials is listed on this page.
Where can I download the Eightbots design files?
From the YuseiIto/eightbots repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Eightbots design in my own project?
Yes, under the terms of its GPL-3.0 license, which YuseiIto chose for the repository.
Can I test firmware for the Eightbots without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k