Control
zeyad-hisham-cyper·Solar-IoT-Smart-Irrigation-System·PCBs/control/control.kicad_pcb
About the Control PCB
Control is an open source ESP32 PCB design by zeyad-hisham-cyper, published on GitHub under the MIT license. It is a 2-layer board measuring 113.7 × 70.2 mm, with 24 components from 19 distinct parts.
Its main chip is the 74HC595, from the ESP32 family. By type, the board carries 7 resistors, 5 capacitors, 4 diodes, 3 connectors, 2 ICs and 2 transistors.
It belongs with the iot & wireless, power & battery and sensors designs in this gallery.
From the project
A distributed, low-power irrigation platform that closes the loop between soil sensors in the field and a phone in your hand. It is built from three cooperating subsystems:
A distributed, low-power irrigation platform that closes the loop between soil sensors in the field and a phone in your hand. It is built from three cooperating subsystems:
1. Zone firmware (ESP32) — battery/solar sensor + valve endpoints that measure soil moisture, temperature and water flow, and open/close a solenoid valve on command. 2. Gateway firmware (ESP32) — the single Internet-connected node. It runs the irrigation decision engine, drives the pump, enforces safety, talks to the zones over ESP-NOW, and mirrors all state to the cloud over Wi-Fi. 3. Flutter mobile app — a real-time…

Main components on the Control
Control bill of materials (BOM)
24 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 74HC595 ESP32-DEVKITC-32E | MODULE_ESP32-DEVKITC-32E | U1 |
| 1 | 74HC595 YAAJ_DCDC_StepDown_LM2596 | YAAJ_DCDC_StepDown_LM2596 | U2 |
| 1 | 2N2222 Q_NMOS_GDS | TO-220-3_Vertical | Q1 |
| 1 | 2N2222 BC547 | TO-92_Inline_Wide | Q2 |
| 1 | SCREW_TERMINAL_01X02 Conn_01x03_Socket | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J3 |
| 1 | CONN_01X15_PIN Conn_01x19_Pin | PinSocket_1x19_P2.54mm_Vertical | J6 |
| 1 | Conn_01x19_Pin | PinSocket_1x19_P2.54mm_Vertical | J7 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | 1N4007 | D_DO-35_SOD27_P7.62mm_Horizontal | D1 |
| 3 | LED | LED_D5.0mm | D4, D5, D6 |
| 1 | 100U 100u | C_Radial_D5.0mm_H5.0mm_P2.00mm | C1 |
| 2 | 100N 100n | C_Disc_D5.0mm_W2.5mm_P5.00mm | C2, C5 |
| 1 | 470U 470u | C_Radial_D5.0mm_H5.0mm_P2.00mm | C3 |
| 1 | 100N 470u | C_Radial_D5.0mm_H5.0mm_P2.00mm | C4 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | 100 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
| 1 | 4.7k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
| 1 | 100k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 3 | 220 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5, R6, R7 |
Control design files
The KiCad project lives in the zeyad-hisham-cyper/Solar-IoT-Smart-Irrigation-System repository on GitHub; these links point at the commit this page was built from.
Control: common questions
What microcontroller does the Control use?
The Control is built around the 74HC595, from the ESP32 family.
How big is the Control PCB?
The Control measures 113.7 × 70.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Control?
24 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Control design files?
From the zeyad-hisham-cyper/Solar-IoT-Smart-Irrigation-System repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Control design in my own project?
Yes, under the terms of its MIT license, which zeyad-hisham-cyper chose for the repository.
Can I test firmware for the Control without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Solar-IoT-Smart-Irrigation-System
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k