Light

zeyad-hisham-cyper·Solar-IoT-Smart-Irrigation-System·PCBs/light/light.kicad_pcb

Light PCB layout, top view — open source ESP8266 board by zeyad-hisham-cyper

About the Light PCB

Light is an open source ESP8266 PCB design by zeyad-hisham-cyper, published on GitHub under the MIT license. It is a 2-layer board measuring 161.4 × 165.1 mm, with 76 components from 17 distinct parts.

Its main chip is the NodeMCU1.0(ESP-12E), from the ESP8266 family. Other key parts include the 74HC595, YAAJ_DCDC_STEPDOWN_LM2596 and PC817. By type, the board carries 28 resistors, 16 LEDs, 8 ICs, 5 capacitors, 4 transistors and 4 relays.

It belongs with the iot & wireless, power & battery and sensors designs in this gallery.

From the project

A distributed, low-power irrigation platform that closes the loop between soil sensors in the field and a phone in your hand. It is built from three cooperating subsystems:

A distributed, low-power irrigation platform that closes the loop between soil sensors in the field and a phone in your hand. It is built from three cooperating subsystems:

1. Zone firmware (ESP32) — battery/solar sensor + valve endpoints that measure soil moisture, temperature and water flow, and open/close a solenoid valve on command. 2. Gateway firmware (ESP32) — the single Internet-connected node. It runs the irrigation decision engine, drives the pump, enforces safety, talks to the zones over ESP-NOW, and mirrors all state to the cloud over Wi-Fi. 3. Flutter mobile app — a real-time…

Light, from the project README
From the project README

Main components on the Light

Light bill of materials (BOM)

76 components, 17 distinct parts — part numbers from the project's BOM.

QtyPartRefs
2
74HC595
U1, U2
1
NodeMCU1.0(ESP-12E)
U3
1
YAAJ_DCDC_STEPDOWN_LM2596
YAAJ_DCDC_StepDown_LM2596
U4
4
PC817
U5, U8, U9, U10
4
2N2222
2n2222
Q1, Q2, Q3, Q4
2
CONN_01X15_PIN
Conn_01x15_Pin
J5, J6
1
SCREW_TERMINAL_01X02
Screw_Terminal_01x02
J8
4
SRD-12VDC-SL-C
K1, K2, K3, K4
4
Screw_Terminal_01x02
ROOM1, ROOM2, ROOM3, ROOM4
16
LED
ROOM14, ROOM 1, ROOM 2, ROOM 3, ROOM 4, ROOM 5, ROOM 6, ROOM 7 +8
4
1N4007
D17, D18, D19, D20
1
100U
100u
C1
3
100N
100n
C2, C4, C5
1
470U
470u
C3
20
1k
R1, R2, R3, R4, R5, R6, R7, R8 +12
4
680
R18, R20, R23, R24
4
100K
100k
R19, R22, R27, R28

Light design files

The KiCad project lives in the zeyad-hisham-cyper/Solar-IoT-Smart-Irrigation-System repository on GitHub; these links point at the commit this page was built from.

Light: common questions

What microcontroller does the Light use?

The Light is built around the NodeMCU1.0(ESP-12E), from the ESP8266 family.

How big is the Light PCB?

The Light measures 161.4 × 165.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Light?

76 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Light design files?

From the zeyad-hisham-cyper/Solar-IoT-Smart-Irrigation-System repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Light design in my own project?

Yes, under the terms of its MIT license, which zeyad-hisham-cyper chose for the repository.

Can I test firmware for the Light without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.

More boards in Solar-IoT-Smart-Irrigation-System

Similar boards