ProgrammaGull E6
4n3m4i1·PG_Logic·Boards/PGL_E6/ProgrammaGull_E6/ProgrammaGull_E6.kicad_pcb
About the ProgrammaGull E6 PCB
ProgrammaGull E6 is an open source FPGA PCB design by 4n3m4i1, published on GitHub under the MIT license. It is a 4-layer board measuring 25.4 × 25.4 mm, with 31 components from 19 distinct parts.
Its main chip is the PGL_E6, from the FPGA family. Other key parts include the C88039, C3303720, C81462, ICE40UP5K-SG48ITR and C43420. By type, the board carries 17 capacitors, 6 ICs, 6 resistors, 1 jumper and 1 diode.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Open Source FPGA Development Boards for Education and Deeply Embedded Applications
Main components on the ProgrammaGull E6
ProgrammaGull E6 bill of materials (BOM)
31 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | PGL_E6 | PGL_E6 | U1 |
| 1 | C88039 MIC5504-2.5YM5 | SOT-23-5 | U2 |
| 1 | C3303720 MIC5504-1.2YM5 | SOT-23-5 | U3 |
| 1 | C81462 W25Q32JVSS | SOIC-8_5.23x5.23mm_P1.27mm | U4 |
| 1 | ICE40UP5K-SG48ITR | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U5 |
| 1 | C43420 AP7375-33SA-7 | SOT-23-3 | U9 |
| 1 | SolderJumper_3_Open | SolderJumper-3_P2.0mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | C2297 1N4148WS | D_SOD-323 | D2 |
| 7 | C15849 1u | C_0603_1608Metric | C1, C2, C3, C4, C5, C6, C19 |
| 4 | C14663 100n | C_0603_1608Metric | C7, C13, C16, C18 |
| 1 | C14663 10n | C_0603_1608Metric | C14 |
| 2 | C1779 100n | C_0603_1608Metric | C15, C17 |
| 2 | C14663 1u | C_0603_1608Metric | C20, C22 |
| 1 | C15849 100n | C_0603_1608Metric | C21 |
| 2 | C25804 10k | R_0603_1608Metric | R1, R8 |
| 1 | C4190 10k | R_0603_1608Metric | R2 |
| 1 | C23206 10k | R_0603_1608Metric | R4 |
| 1 | C22775 10k | R_0603_1608Metric | R5 |
| 1 | C25804 100R | R_0603_1608Metric | R7 |
ProgrammaGull E6 design files
The KiCad project lives in the 4n3m4i1/PG_Logic repository on GitHub; these links point at the commit this page was built from.
ProgrammaGull E6: common questions
What microcontroller does the ProgrammaGull E6 use?
The ProgrammaGull E6 is built around the PGL_E6, from the FPGA family.
How big is the ProgrammaGull E6 PCB?
The ProgrammaGull E6 measures 25.4 × 25.4 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the ProgrammaGull E6?
31 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ProgrammaGull E6 design files?
From the 4n3m4i1/PG_Logic repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ProgrammaGull E6 design in my own project?
Yes, under the terms of its MIT license, which 4n3m4i1 chose for the repository.
Can I test firmware for the ProgrammaGull E6 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug FPGA firmware against it before you order a PCB.
More boards in PG_Logic
Similar boards
FPGA
Base board
GlasgowEmbedded
80 × 49 mm222 parts4L0BSD2.2kFPGA
Thunderscope Rev5.3
EEVengers
122.5 × 103.5 mm817 parts6LMIT1.3kFPGA
Usb sniffer
ataradov
58.2 × 38.1 mm86 parts2LBSD-3-Clause1.3kFPGA
Tomu, I'm
theacodes
13 × 9.4 mm40 parts4LMIT1.1kFPGA
Icepi zero
cheyao
65 × 30 mm143 parts4LSHL-2.1865FPGA
Gcvideo
ikorb
49 × 30 mm44 parts4LNo license765