ProgrammaGull E3
4n3m4i1·PG_Logic·Boards/ProgrammaGull_E3/ProgrammaGull_E3/ProgrammaGull_E3.kicad_pcb
About the ProgrammaGull E3 PCB
ProgrammaGull E3 is an open source FPGA PCB design by 4n3m4i1, published on GitHub under the MIT license. It is a 4-layer board, with 63 components from 34 distinct parts.
Its main chip is the ICE40UP5K-SG48ITR, from the FPGA family. Other key parts include the C88039, C3303720, C81462, C190271 and C193662. By type, the board carries 36 capacitors, 14 resistors, 8 ICs, 3 connectors and 2 diodes.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Open Source FPGA Development Boards for Education and Deeply Embedded Applications
Main components on the ProgrammaGull E3
ProgrammaGull E3 bill of materials (BOM)
63 components, 34 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ICE40UP5K-SG48ITR | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 1 | C88039 W25Q32JVSS | SOIC-8_5.23x5.23mm_P1.27mm | U2 |
| 1 | C3303720 AP2127K-3.3 | SOT-23-5 | U3 |
| 1 | C81462 AP2127K-2.5 | SOT-23-5 | U4 |
| 1 | ~ | TDFN-16-1EP_3x2_mm | U5 |
| 1 | C190271 AP2127K-1.2 | SOT-23-5 | U6 |
| 1 | C193662 LM324A | TSSOP-14_4.4x5mm_P0.65mm | U7 |
| 1 | C401125 ~ | LFCSP-WD-10-1EP_3x3mm_P0.5mm_EP1.64x2.38mm | U8 |
| 1 | C2897434 Conn_01x24_Pin | PinSocket_1x24_P2.54mm_Vertical | J1 |
| 1 | Conn_02x04_Counter_Clockwise | PinSocket_2x04_P2.54mm_Vertical | J2 |
| 1 | Conn_01x24_Pin | PinSocket_1x24_P2.54mm_Vertical | J3 |
| 1 | C81598 1N4148WT | D_SOD-523 | D1 |
| 1 | C2297 LED_AGBR | LED_Cree-PLCC4_2x2mm_CW | D3 |
| 4 | C15849 2u2 | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C4, C19, C21 |
| 3 | C15849 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C5, C24 |
| 2 | C15849 10n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C6 |
| 7 | C14663 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7, C16, C18, C20, C22, C31, C32 |
| 1 | C14663 10n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C8 |
| 6 | C14663 2u2 | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9, C11, C13, C14, C26, C34 |
| 4 | C1779 2u2 | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10, C12, C15, C33 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | C1779 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C17, C30 |
| 1 | C15849 1u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C23 |
| 3 | C1779 1u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C25, C27, C35 |
| 3 | C14663 1u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C28, C29, C36 |
| 1 | C25804 R_Small | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | C4190 R_Small | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | C23206 R_Small | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | C23206 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
| 1 | C22775 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5 |
| 1 | C22962 R_Small | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 3 | C25804 100R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R8, R12 |
| 2 | C22962 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9, R11 |
| 1 | C25804 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10 |
| 2 | 10k | R_Array_Convex_2x0603 | RN1, RN2 |
ProgrammaGull E3 design files
The KiCad project lives in the 4n3m4i1/PG_Logic repository on GitHub; these links point at the commit this page was built from.
ProgrammaGull E3: common questions
What microcontroller does the ProgrammaGull E3 use?
The ProgrammaGull E3 is built around the ICE40UP5K-SG48ITR, from the FPGA family.
How big is the ProgrammaGull E3 PCB?
The ProgrammaGull E3 has 4 copper layers and is 1.6 mm thick.
How many components are on the ProgrammaGull E3?
63 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ProgrammaGull E3 design files?
From the 4n3m4i1/PG_Logic repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ProgrammaGull E3 design in my own project?
Yes, under the terms of its MIT license, which 4n3m4i1 chose for the repository.
Can I test firmware for the ProgrammaGull E3 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug FPGA firmware against it before you order a PCB.
More boards in PG_Logic
Similar boards
FPGA
Base board
GlasgowEmbedded
80 × 49 mm222 parts4L0BSD2.2kFPGA
Thunderscope Rev5.3
EEVengers
122.5 × 103.5 mm817 parts6LMIT1.3kFPGA
Usb sniffer
ataradov
58.2 × 38.1 mm86 parts2LBSD-3-Clause1.3kFPGA
Tomu, I'm
theacodes
13 × 9.4 mm40 parts4LMIT1.1kFPGA
Icepi zero
cheyao
65 × 30 mm143 parts4LSHL-2.1865FPGA
Gcvideo
ikorb
49 × 30 mm44 parts4LNo license765