RoboArm
9Akshit1·RoboArm·schematic_pcb/RoboArm/RoboArm.kicad_sch

About the RoboArm PCB
RoboArm is an open source ESP32 PCB design by 9Akshit1, published on GitHub under the MIT license. It is a board, with 37 components from 13 distinct parts.
Its main chip is the ESP32-DEVKIT-V1, from the ESP32 family. Other key parts include the 815 PCA9685, 2472 BNO055, ADS1115IDGS, TXS0108EPW and ESP32-CAM. By type, the board carries 9 ICs, 9 modules, 3 capacitors and 2 resistors.
It belongs with the robotics & motion designs in this gallery.
From the project
The arm compartment of my RoboHand
INSPIRATION: I've always been inspired by how human arms move and wanted to recreate that motion using motors and tendons. Additionally, I previosuly built a RoboHand so to add on to that project, I wanted to add a RoboArm to extend it. I also wanted to get into the neuroscience field, so this is my first step into it!
Also, PLEASE NOTE that I can always just add supports before I 3D print, so we do not need to worry about any floating or thin pieces because they were likely intended by me to be there!
Main components on the RoboArm
RoboArm bill of materials (BOM)
37 components, 13 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-DEVKIT-V1 | MODULE_ESP32_DEVKIT_V1 | U1 |
| 1 | 815 PCA9685 | MODULE_815 | U2 |
| 1 | 2472 BNO055 | MODULE_2472 | U3 |
| 3 | ADS1115IDGS | TSSOP-10_3x3mm_P0.5mm | U4, U6, U7 |
| 1 | TXS0108EPW | TSSOP-20_4.4x6.5mm_P0.65mm | U8 |
| 1 | ESP32-CAM | ESP32-CAM | U9 |
| 1 | LM2596S-ADJ | TO-263-5_TabPin3 | U10 |
| 9 | Motor_Servo | M1, M2, M3, M4, M5, M6, M7, M8 +1 | |
| 14 | ~ | LX-255_Servo_Motor1, LX-255_Servo_Motor2, LX-255_Servo_Motor3, LX-255_Servo_Motor4, MyoWare EMG Sensor1, MyoWare EMG Sensor2, MyoWare EMG Sensor3, MyoWare EMG Sensor4 +6 | |
| 1 | 1000µF | C1 | |
| 1 | 470µF | C2 | |
| 1 | 220µF | C3 | |
| 2 | 4.7kΩ | R1, R2 |
RoboArm design files
The KiCad project lives in the 9Akshit1/RoboArm repository on GitHub; these links point at the commit this page was built from.
- Schematicschematic_pcb/RoboArm/RoboArm.kicad_sch
- BOMBOM.csv
RoboArm: common questions
What microcontroller does the RoboArm use?
The RoboArm is built around the ESP32-DEVKIT-V1, from the ESP32 family.
How many components are on the RoboArm?
37 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the RoboArm design files?
From the 9Akshit1/RoboArm repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the RoboArm design in my own project?
Yes, under the terms of its MIT license, which 9Akshit1 chose for the repository.
Can I test firmware for the RoboArm without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k