Desk Guardian Sentry - Networked Sentry

AlexOpanasevych·beetroot_embedded_course·main_project/pcb/desk_guardian_sentry.kicad_pcb

Desk Guardian Sentry - Networked Sentry PCB layout, top view — open source ESP32 board by AlexOpanasevych

About the Desk Guardian Sentry - Networked Sentry PCB

Desk Guardian Sentry - Networked Sentry is an open source ESP32 PCB design by AlexOpanasevych, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 78 × 106 mm, with 33 components from 19 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AMS1117-3.3. By type, the board carries 12 resistors, 7 capacitors, 4 connectors, 2 ICs, 2 transistors and 2 LEDs.

It belongs with the sensors and iot & wireless designs in this gallery.

From the project

Module tasks for Beetroot Embedded course

A capstone that extends the miniprojectmodule5** "Desk Guardian" PIR/buzzer/LED board into a small networked environmental sentry: it still barks at motion, but now also reads temperature/humidity/pressure, spins a PID-controlled cooling fan, and serves a live status dashboard over Wi-Fi — no PC/serial monitor required to see what it's doing.

Hardware is Desk Guardian PCB rev B (pcb/): the miniproject_module5 board with the PIR/buzzer/LED circuitry unchanged, plus an on-board BME280 header and a fan low-side driver for the new features — see PCB — rev B.

Main components on the Desk Guardian Sentry - Networked Sentry

Desk Guardian Sentry - Networked Sentry bill of materials (BOM)

33 components, 19 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AMS1117-3.3
U1
1
ESP32-S3-WROOM-1
U2
2
MMBT3904
Q1, Q2
1
USB_C_Receptacle_PowerOnly_6P
J1
1
PIR_Sensor
J2
1
BME280
J3
1
Fan
J4
1
Buzzer
BZ1
1
SW_PUSH
SW1
2
LED_Red
LED1, LED2
2
1N4148
D1, D2
3
10uF
C1, C2, C7
4
100nF
C3, C4, C5, C6
2
5.1k
R1, R2
3
10k
R3, R4, R12
1
100k
R5
2
1k
R6, R11
2
220
R7, R8
2
4.7k
R9, R10

Desk Guardian Sentry - Networked Sentry design files

The KiCad project lives in the AlexOpanasevych/beetroot_embedded_course repository on GitHub; these links point at the commit this page was built from.

Desk Guardian Sentry - Networked Sentry: common questions

What microcontroller does the Desk Guardian Sentry - Networked Sentry use?

The Desk Guardian Sentry - Networked Sentry is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Desk Guardian Sentry - Networked Sentry PCB?

The Desk Guardian Sentry - Networked Sentry measures 78 × 106 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Desk Guardian Sentry - Networked Sentry?

33 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Desk Guardian Sentry - Networked Sentry design files?

From the AlexOpanasevych/beetroot_embedded_course repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Desk Guardian Sentry - Networked Sentry design in my own project?

Yes, under the terms of its GPL-3.0 license, which AlexOpanasevych chose for the repository.

Can I test firmware for the Desk Guardian Sentry - Networked Sentry without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in beetroot_embedded_course

Similar boards