Esp32s3 power ldo
AlexOpanasevych·beetroot_embedded_course·module5.2/ldo-variant/esp32s3_power_ldo.kicad_pcb
About the Esp32s3 power ldo PCB
Esp32s3 power ldo is an open source ESP32 PCB design by AlexOpanasevych, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 42 × 54 mm, with 10 components from 8 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AMS1117-3.3. By type, the board carries 3 capacitors, 3 resistors, 2 ICs, 1 connector and 1 switch.
It belongs with the power & battery designs in this gallery.
From the project
Module tasks for Beetroot Embedded course
This routes the schematic from Module 5.1 (esp32s3powerldo.kicadsch / .kicadpro, copied unchanged into this folder so the project is self-contained and openable as one KiCad project) into a fully-routed, DRC-clean 2-layer PCB (esp32s3powerldo.kicadpcb`).
The board was built and routed programmatically with KiCad 10's pcbnew Python API (real footprints loaded straight from the system footprint libraries, real pad geometry, real tracks/vias) rather than hand-edited — see the "How it was built" note at the end.
Main components on the Esp32s3 power ldo
Esp32s3 power ldo bill of materials (BOM)
10 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U2 |
| 1 | USB_C_Receptacle_PowerOnly_6P | USB_C_Receptacle_GCT_USB4125-xx-x_6P_TopMnt_Horizontal | J1 |
| 1 | SW_PUSH | SW_SPST_B3U-1000P | SW1 |
| 2 | 10uF | C_0805_2012Metric | C1, C2 |
| 1 | 100nF | C_0603_1608Metric | C3 |
| 2 | 5.1k | R_0603_1608Metric | R1, R2 |
| 1 | 10k | R_0603_1608Metric | R3 |
Esp32s3 power ldo design files
The KiCad project lives in the AlexOpanasevych/beetroot_embedded_course repository on GitHub; these links point at the commit this page was built from.
Esp32s3 power ldo: common questions
What microcontroller does the Esp32s3 power ldo use?
The Esp32s3 power ldo is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Esp32s3 power ldo PCB?
The Esp32s3 power ldo measures 42 × 54 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32s3 power ldo?
10 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32s3 power ldo design files?
From the AlexOpanasevych/beetroot_embedded_course repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32s3 power ldo design in my own project?
Yes, under the terms of its GPL-3.0 license, which AlexOpanasevych chose for the repository.
Can I test firmware for the Esp32s3 power ldo without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in beetroot_embedded_course
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k